Infinite Peripherals SCOM-100 manual Troubleshooting

Page 66

SCOM-100, User guide		66
9.2 Troubleshooting

	The ready LED goes off	Case 1: Error LED is off
	after the start up	You started the unit for the first time
	sequence.	and the SIM card does not contain
		a user name and phone number in
		the phone book directory. See
		chapter 3.1.
		Case 2: Error LED is on
		An error occurred during start up.
		See chapter 9.4 & 9.5.

	The unit does not	The unit does not register to the
	respond to SMS at all.	GSM provider network. Check if the
		‘NETWORK’ LED is blinking.
		Connect a proper GSM antenna to
		the unit (See chapter 2.6)

	The unit does not	The ‘Response SMS’ parameter is
	respond to configuration	probably off. Set the parameter to
	SMS commands.	on state.
		Read chapter 6.2.1

	The unit does not	Check the status LED.
	execute my digital	The unit is probably in STOP or
	output control	MONITOR status. Set the unit
	commands.	status to RUN. See chapter 6.1.
		Read the SMS response to your
		command.

Image 66

Contents Page Disclaimer Contents Page Page Device overview ConnectionsLED indications Wiring Power supplyDigital inputs Digital outputs AC1Analog inputs Analog inputVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna MicrophoneInstalling the SIM card Getting startedPreparing a SIM card First power up & factory settings Naming the unit SMS commandsDevice operation XXXX,A..A,..,..,Z..ZConfiguring a digital input for alarming 1100,m,n,s,a,d1100,0,1,Door contact,3,30 My SCOM-100 Door contactSetting alarm message’s texts 0630,ID,s1101,m,n,ID1,ID2 My SCOM-100 Door contact Door is opened 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100Clearing the digital input configuration Door contact Door is closed1110,m,n 1000,m,n Setting a digital outputControlling the digital outputs 1000,0,21071,m,n Configuring an output as a closed contact1001,0,2 1071,0,21070,m,n Pulse digital outputSetting a digital output after a delay 1010,m,n,s1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moffTime schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D1700,1,0,800-120,1130-1001645-180 1030,m,n,ID1701,ID,P Clearing the digital output configuration 1701,3,501090,m,n,ID Analog signal alarming Analog input configuration1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide Setting alarm message’s texts for analog inputs 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,151201,m,n,ID1,ID2 1210,m,n Clearing the analog input configurationSetting the analog inputs alarm deadband 1800,dSpecial I/O Functions 1 ON/OFF and PID control1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s1252,id,m,n 1253,id1260,id User administration Create a new user0500,id,n,p,c1,c2,c3 Set a DI alarm recipient Change user configurationDefining specific alarm recipients Delete a userSet an AI alarm recipient Clear DI alarm recipientsClear AI alarm recipients RUN Control command Device status & mode controlsSetting the device status Monitor command1105,m,n,v Controlling the device statusControlling the device response Send acknowledgement SMSSetting up an SMS counter Merge concurrent alarmsResponse format Setting date and time Setting a GSM PIN5100 Monitoring commandsMonitoring capabilities UNITMy SCOM-100Connecting a PC Using the Hyperterminal for configurationSCOM-100, User guide SCOM-100, User guide Using the Scom Configurator for configuration Ate1Atsms=1100,0,1,Door contact,3,30 Using the microphone input Command reference General parameter settingsAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unitGE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LEDDefault parameter values Factory settings GE-DIO-42 Digital I/O expansionSetting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN