Infinite Peripherals SCOM-100 manual Digital outputs, AC1

Page 10

SCOM-100, User guide

10

2.3 Digital outputs

SCOM-100 has 4 built in digital outputs, which can be expanded by the DIO-42 expansion modules. The digital outputs are wired by means of screw terminals. Each output has a normally open contact power relay.

Voltage	Current	Mode

250VAC	10A	AC1

250VAC	1A	AC2,3

150VDC	0.5A	DC

It is recommended to use external power relays to drive inductive or capacitive loads demanding more than 0.5A.

Image 10

Contents Page Disclaimer Contents Page Page Device overview ConnectionsLED indications Wiring Power supplyDigital inputs Digital outputs AC1Analog inputs Analog inputVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide GSM antenna MicrophoneGetting started Installing the SIM cardPreparing a SIM card First power up & factory settings Naming the unit SMS commandsDevice operation XXXX,A..A,..,..,Z..ZConfiguring a digital input for alarming 1100,m,n,s,a,d1100,0,1,Door contact,3,30 My SCOM-100 Door contact0630,ID,s Setting alarm message’s texts1101,m,n,ID1,ID2 My SCOM-100 Door contact Door is opened 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100Door contact Door is closed Clearing the digital input configuration1110,m,n 1000,m,n Setting a digital outputControlling the digital outputs 1000,0,21071,m,n Configuring an output as a closed contact1001,0,2 1071,0,21070,m,n Pulse digital output1010,m,n,s Setting a digital output after a delay1010,0,2,25 Resetting a digital output after a delay 1020,m,n,h,mn1021,m,n,h,mn Digital output time based scheduling 1040,m,n,mon,moffTime schedule program 1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D1030,m,n,ID 1700,1,0,800-120,1130-1001645-1801701,ID,P 1701,3,50 Clearing the digital output configuration1090,m,n,ID Analog input configuration Analog signal alarming1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 Setting alarm message’s texts for analog inputs1201,m,n,ID1,ID2 1210,m,n Clearing the analog input configurationSetting the analog inputs alarm deadband 1800,d1 ON/OFF and PID control Special I/O Functions1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1255,id,sp 1251,id,s1253,id 1252,id,m,n1260,id Create a new user User administration0500,id,n,p,c1,c2,c3 Set a DI alarm recipient Change user configurationDefining specific alarm recipients Delete a userClear DI alarm recipients Set an AI alarm recipientClear AI alarm recipients RUN Control command Device status & mode controlsSetting the device status Monitor command1105,m,n,v Controlling the device statusControlling the device response Send acknowledgement SMSMerge concurrent alarms Setting up an SMS counterResponse format Setting date and time Setting a GSM PIN5100 Monitoring commandsMonitoring capabilities UNITMy SCOM-100Connecting a PC Using the Hyperterminal for configurationSCOM-100, User guide SCOM-100, User guide Ate1 Using the Scom Configurator for configurationAtsms=1100,0,1,Door contact,3,30 Using the microphone input General parameter settings Command referenceAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Technical specifications Main unitGE-DIO-42 Digital I/O Expansion module Error handling Status LED indications LEDDefault parameter values Factory settings GE-DIO-42 Digital I/O expansionSetting an I/O expansion module address Dip switch settings Module number m RS232C connector layout PIN