Infinite Peripherals SCOM-100 manual Device status & mode controls, Setting the device status

Page 47

SCOM-100, User guide

6. Device status & mode controls

6.1 Setting the device status

ASCOM-100 unit has three operation states:

1.The RUN (Control) state: The unit sends alarm SMS and accepts output control commands. The Status LED is then on.

2.The MONITOR state: The unit sends alarm SMS. All outputs are reset to their initial state. Output control commands are executed by storing the output states internally. The actual output states are restored upon switching to the RUN state. The Status LED is blinking.

3.The STOP state: The unit does not send SMS and rejects all output control commands. All outputs are reset to their initial state. The Status LED is then off.

Configuration and monitoring commands are accepted and answered in all operation modes.

6.1.1RUN (Control) command

0100

The Status LED switches on and the unit enters the RUN (Control) state.

6.1.2Monitor command

0110

The Status LED starts blinking and the unit enters the MONITOR state.

6.1.3 STOP command

0000

Image 47

Contents Page Disclaimer Contents Page Page Connections Device overviewLED indications Power supply WiringDigital inputs AC1 Digital outputsAnalog input Analog inputsVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antennaPreparing a SIM card Installing the SIM cardGetting started First power up & factory settings XXXX,A..A,..,..,Z..Z SMS commandsDevice operation Naming the unit1100,m,n,s,a,d Configuring a digital input for alarmingMy SCOM-100 Door contact 1100,0,1,Door contact,3,301101,m,n,ID1,ID2 Setting alarm message’s texts0630,ID,s My SCOM-100 0630,1,Door is opened 0630,2,Door is closed0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 My SCOM-100 Door contact Door is opened1110,m,n Clearing the digital input configurationDoor contact Door is closed 1000,0,2 Setting a digital outputControlling the digital outputs 1000,m,n1071,0,2 Configuring an output as a closed contact1001,0,2 1071,m,nPulse digital output 1070,m,n1010,0,2,25 Setting a digital output after a delay1010,m,n,s 1020,m,n,h,mn Resetting a digital output after a delay1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program1701,ID,P 1700,1,0,800-120,1130-1001645-1801030,m,n,ID 1090,m,n,ID Clearing the digital output configuration1701,3,50 1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d Analog signal alarmingAnalog input configuration ALH SCOM-100, User guide 1201,m,n,ID1,ID2 Setting alarm message’s texts for analog inputs1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,15 1800,d Clearing the analog input configurationSetting the analog inputs alarm deadband 1210,m,n1250,id,m,n,m1,n1,sp,g,it,dt,ct,h Special I/O Functions1 ON/OFF and PID control 1251,id,s 1255,id,sp1260,id 1252,id,m,n1253,id 0500,id,n,p,c1,c2,c3 User administrationCreate a new user Delete a user Change user configurationDefining specific alarm recipients Set a DI alarm recipientClear AI alarm recipients Set an AI alarm recipientClear DI alarm recipients Monitor command Device status & mode controlsSetting the device status RUN Control commandSend acknowledgement SMS Controlling the device statusControlling the device response 1105,m,n,vResponse format Setting up an SMS counterMerge concurrent alarms Setting a GSM PIN Setting date and timeUNITMy SCOM-100 Monitoring commandsMonitoring capabilities 5100Using the Hyperterminal for configuration Connecting a PCSCOM-100, User guide SCOM-100, User guide Atsms=1100,0,1,Door contact,3,30 Using the Scom Configurator for configurationAte1 Using the microphone input Appendix Command referenceGeneral parameter settings SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specificationsGE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indicationsGE-DIO-42 Digital I/O expansion Default parameter values Factory settingsSetting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout