Infinite Peripherals SCOM-100 Change user configuration, Delete a user, Set a DI alarm recipient

Page 45

SCOM-100, User guide

45

5.2 Change user configuration

A user with the user administration privilege can use this command to edit other user privileges.

0502,id,c1,c2,c3

0502:	Command ID
id:	User ID (1-20)
c1:	User administration privilege (0 for ‘No’
	1 for ‘Yes’)
c2:	Device configuration privilege (0 for
	‘No’ 1 for ‘Yes’)
c3:	Alarm SMS recipient (0 for ‘No’ 1 for
	‘Yes’)

5.3 Delete a user

A user with the user administration privilege can use this command to remove a user from the user list.

0501,id
0501:	Command ID
id:	User ID (1-20)

5.4 Defining specific alarm recipients

Special commands are available for defining a subset of the user list as SMS recipients for each alarm.

5.4.1Set a DI alarm recipient

1102,m,n,id

1102:	Command ID
m:	Module number (0 for SCOM-100 main
	unit, 1-8 for DI-42 I/O expansion units)

Image 45

Contents Page Disclaimer Contents Page Page Connections Device overviewLED indications Power supply WiringDigital inputs AC1 Digital outputsAnalog input Analog inputsVin SCOM-100, User guide Analog input I/O expansion power supply SCOM-100, User guide Microphone GSM antennaInstalling the SIM card Getting startedPreparing a SIM card First power up & factory settings Device operation SMS commandsNaming the unit XXXX,A..A,..,..,Z..Z1100,m,n,s,a,d Configuring a digital input for alarmingMy SCOM-100 Door contact 1100,0,1,Door contact,3,30Setting alarm message’s texts 0630,ID,s1101,m,n,ID1,ID2 0630,1,Door is opened 0630,2,Door is closed 1101,0,1,2,1 0630,1,Door is opened 0630,2,Door is closedMy SCOM-100 Door contact Door is opened My SCOM-100Clearing the digital input configuration Door contact Door is closed1110,m,n Controlling the digital outputs Setting a digital output1000,m,n 1000,0,21001,0,2 Configuring an output as a closed contact1071,m,n 1071,0,2Pulse digital output 1070,m,nSetting a digital output after a delay 1010,m,n,s1010,0,2,25 1020,m,n,h,mn Resetting a digital output after a delay1021,m,n,h,mn 1040,m,n,mon,moff Digital output time based scheduling1700,ID,d,P1B-P1D,P2B-P2D,…,P8B-P8D Time schedule program1700,1,0,800-120,1130-1001645-180 1030,m,n,ID1701,ID,P Clearing the digital output configuration 1701,3,501090,m,n,ID Analog signal alarming Analog input configuration1200,m,n,s,SSL,SSH,SCL,SCH,ALL,ALH,u,d ALH SCOM-100, User guide Setting alarm message’s texts for analog inputs 1200,0,2,Pressure,819,4095,0,10000,2500 8500,mBar,151201,m,n,ID1,ID2 Setting the analog inputs alarm deadband Clearing the analog input configuration1210,m,n 1800,dSpecial I/O Functions 1 ON/OFF and PID control1250,id,m,n,m1,n1,sp,g,it,dt,ct,h 1251,id,s 1255,id,sp1252,id,m,n 1253,id1260,id User administration Create a new user0500,id,n,p,c1,c2,c3 Defining specific alarm recipients Change user configurationSet a DI alarm recipient Delete a userSet an AI alarm recipient Clear DI alarm recipientsClear AI alarm recipients Setting the device status Device status & mode controlsRUN Control command Monitor commandControlling the device response Controlling the device status1105,m,n,v Send acknowledgement SMSSetting up an SMS counter Merge concurrent alarmsResponse format Setting a GSM PIN Setting date and timeMonitoring capabilities Monitoring commands5100 UNITMy SCOM-100Using the Hyperterminal for configuration Connecting a PCSCOM-100, User guide SCOM-100, User guide Using the Scom Configurator for configuration Ate1Atsms=1100,0,1,Door contact,3,30 Using the microphone input Command reference General parameter settingsAppendix SMS User configuration Output control & configuration Input configuration 5 I/O Functions RTC & Time scheduling Monitoring commands AI/DI/AO/DO Troubleshooting Page Main unit Technical specificationsGE-DIO-42 Digital I/O Expansion module Error handling LED Status LED indicationsGE-DIO-42 Digital I/O expansion Default parameter values Factory settingsSetting an I/O expansion module address Dip switch settings Module number m PIN RS232C connector layout