Sony MAV-555SS operation manual Contents of the Expansion Menu

Chapter 3 Preparations

3-4-3 Contents of the Expansion Menu

The contents of the Expansion menu are described in the table that follows.

•The item enclosed in a square in the “Settings” column indicates defaults.

•The letters “B” and “I” in the item number column indicate when a change to

		that setting becomes effective, just as in the Basic menu.
		For details on the meaning of each letter, refer to Section 3-4-1, “Basic Menu Settings” (page
		3-18).
		Expansion menu items
Item number	Display indication	Settings	Description
101	SELECTION FOR SEARCH	This item sets the method for putting the MAV-555SS into search mode.
BI	DIAL ENABLE	dial direct	: The unit enters search mode when the search dial is turned from any
			mode except while recording/editing are in progress.
		via search key : The unit enters search mode when any of the following buttons is
			pressed: JOG, SHUTTLE, VAR.
102	SHUTTLE MODE	This item specifies the startup characteristics when		v	mode 1
BI	SYNCHRONIZE	entering shuttle mode.
		mode 1	: Normal disk characteristics
		mode 2	: Squared acceleration
		mode 3	: Linear acceleration		mode 3	mode 2
						t

105	SYNCHRONIZE	This item specifies, for playback and for variable speed playback (JOG/VAR) with
	B	FORT synchronization control, whether to apply speed limitations when reversing the
		playback direction or to not apply speed limitations and give priority to response.
		off	: Apply no speed limitations, and give priority to response.
		on	: Apply speed limitation.
		Note:	When playing back material recorded in SS mode, this setting reverts to off.
106	MAXIMUM SHUTTLE SPEED	This item specifies the maximum shuttle speed.
	BI	×8	: Maximum shuttle speed is 8×.
		×16	: Maximum shuttle speed is 16×.
		×32	: Maximum shuttle speed is 32×.
		×50	: Maximum shuttle speed is 50×.
		×100	: Maximum shuttle speed is 100×.
		×200	: Maximum shuttle speed is 200×.
		×500	: Maximum shuttle speed is 500×.
		Note:	With some editing equipment, if a maximum speed of 100× or greater is set,
			the speed is deemed to be impossible for FF or REW, and the TC display
			disappears. If using equipment in which this happens, set a speed of less
			than 100×.
107	MAXIMUM JOG SPEED	Sets the maximum JOG speed.
	BI	×1, ×2,	×4 , SHUTTLE
		When SHUTTLE is selected, the maximum speed set in SETUP MENU 106 is applied.
		Note:	This means that synchronization is not possible during linear editing when the
			JOG speed is set to ×2 (or greater). For linear editing, set the JOG speed to ×1.
108	AUTO EE SELECT	This item sets the conditions for switching to the REC port when PB/EF SELECT (menu
	BI	013) is set to PB/EE.
		stop/f.fwd/rew		: Switch the PB side to the EE side during STOP/FAST FORWARD/
				REWIND.
		stop		: Switch the PB side to the EE side during STOP.
109	ENFORCED EE INTERFACE	Enables the ENFORCED function of the EE command specified from the 9PIN terminal
	BI	and meter panel in the Panel mode. This menu setting and the control panel setting
		match and determine the ENFORCED EE function from the control panel.
		enable	: Enables ENFORCED EE
		disable	: Ignores the command.
120	OUTPUT REF LOCK	This item specifies whether to synchronize the output system video refresh with the REF
	I	input jack, the R1 video input jack, or the R2 video input jack.
		REF	: Synchronize with the reference video signal input through the REF IN jack.
		R1	: Synchronize with the video signal input through R1.
		R2	: Synchronize with the video signal input through R2.
		Note:	When the configuration is 3 input/1 output, the R3 port cannot be specified.

3-26 (E) 3-4 Setup