Sony MAV-555SS Adjusting Playback Audio Levels, Remotely Controlling Video Processor

Page 76

Chapter 4 Recording & Playback

3 Press the TIMER SEL button, to select the type of user bits you want to display. Each time you press the TIMER SEL button switches between the following indications in the display panel for the playback port for which the setting is currently being made: LTC and VITC.

When LTC appears, the LTC user bits are displayed, and when VITC appears, the VITC user bits are displayed.

4-2-5 Adjusting Playback Audio Levels

After choosing a playback port, if the AUDIO REC/PB LEVEL adjustment control is pressed so that the PRESET indicator lights, the audio signal is played back at the preset reference level (shown as reference 0 dB for an input of +4 dBm).

For details of how to set the reference output level for the preset level (changing head room), refer to the Installation Manual.

To adjust the playback level manually

For each channel, press the AUDIO REC/PB LEVEL adjustment control, so that the PRESET indicator goes off, then adjust to the desired level.

4-2-6 Selecting the External Device

Used for Controlling Playback

Operations

Use the following procedure to determine whether you should use the optional control panel (BKMA-505) or the DTR-3000 when recording with this unit.

1 With the PORT SELECT buttons, select the playback port to which the setting applies.

2 Press the REMOTE button, turning it on or off. When lit:

The unit is controlled from the DTR-3000 connected to the REMOTE IN (P1/P2) connector on the unit’s rear connector panel.

When off:

This unit is controlled from the optional control panel (BKMA-505).

4-2-7 Remotely Controlling the

Video Processor

This section explains how to control the internal digital video processor with the HD Digital Video Controller HKDV-503/900 (sold separately).

1 Connect the HD Digital Video Controller HKDV- 503/900 to the VIDEO CONTROL connector (D- SUB 25-pin) of the Connector Panel.

For details, refer to the HKDV-503/900 Installation Manual.

2 Press the PROCESS CONTROL button to select REMOTE. The button lights.

3 Press the D2 button on the HD Digital Video Controller HKDV-503/900 to switch to the D2 mode and make VIDEO PROCESS settings. Furthermore, Unity values can be changed from setup menu items 747 to 764.

Note

•The HD Digital Video Controller HKDV-503 must be at least version 2.00, and the HKDV-900 must be at least version 1.10.

•With the MAV-555SS, CROSS COLOR cannot be

adjusted

For details about the setup menu, refer to Section 3-4, “Setup” (page 3-18).

4-6 (E) 4-2 Preparations for Playback

Page 75 Page 77
Image 76
Page 75 Page 77
Contents MAV-555SSVer Avertissement For the customers in the USA For the customers in EuropePour les clients européens Für Kunden in EuropaTable of Contents Purpose and intended audience for this manual Organization of this manualUsing this manual Descriptions of operating proceduresMaintenance Manual Option Installation Manual suppliedRelated manuals Page SS mode only FeaturesMAV-555SS Overview Common to SS and SD modes SD mode only Changes from Ver Optional AccessoriesChanges from Ver .00 to Ver Editing Fader Panel BKNE-1011 E 1-4 Optional Accessories Names and Functions of Parts Front PanelMeter Panel Port SelectTimer SEL time data display select button ERROR/WARNING indicators System indicatorHDD indicator LED indicators Operating panel indicatorsDisplay indicators panel IndicatorsTime data indication Status indicationPB/REC indicators Video Process setting sectionSetup LEVEL/BLACK Level button Chroma Phase buttonBlank Panel System Setup PanelRemote button Power switch Control Panel connectorControl Panel switch SET UP Select switchConnector Panel SDI OUT connectorsVideo in Composite connectors BNC type Video OUT Composite connectors BNC typeAudio in AES/EBU Digital Audio Input connectors BNC type Audio OUT AES/EBU connectors BNC typeSDI Super connector Analog Composite Super connectorDSK in connectors Sdti CP connectorsAnalog Audio Expansion Box BKMA-570 Page Motion modes Two modes MAV-555SS ModesOperation modes Four modes Panel Mode SS Mode Sony Super Motion ModeSD Mode Standard Motion mode VTRSS Mode DTR + Panel ModeSD Mode MAV-555SS Modes 3-5 E DTR + DTR Mode SD mode only BVE Mode SD mode only MAV-555SSEditing Panel Monitor Ntsc BLOCK-1 Connecting External Devices Connections with the Panel ModeConnecting to digital devices SS mode 10 EConnecting to digital devices SD mode OUTConnecting to analog devices SD mode Analog Audio OUTConnecting with the DTR+Panel mode SS mode Connections with the DTR + Panel Mode13 E Connecting with the DTR+Panel mode SD mode Sync Generator Dynamic Motion Controller DTR-3000Connections with the DTR + DTR Mode 15 EBVE Mode Connections External Synchronization of Output Video Signals Setup Basic Menu Settings18 E 3-4 Setup How to Read the TablesLocal Function Enable Drop Frame Mode withPreroll Time Character H-POSITION20 E 3-4 Setup Port Configuration DTR CUE List ClearLive Duration DTR-1 Loop REC22 E 3-4 Setup Basic Menu Operation To cancel setting changesModes of operating the Menu control Menus including a setting submenu 24 E 3-4 SetupMenu items with submenus Press the Menu knob Contents of the Expansion Menu Load Setup ALL Save Setup ALLLoad Setup Bank Setup Bank28 E 3-4 Setup Configuration GPI OutputPIN 9 . Function PIN 26 . Function30 E 3-4 Setup Audio Fade Mode P1 Audio Fade Mode P2Audio Fade Mode P3 Preset Replace32 E 3-4 Setup SUB Menu Edit Delay Edit Preset CommendFunction Mode After Function Mode After Cueup P334 E 3-4 Setup Setting NON Compress Line R1NON Compress Line R2 F1 Select36 E 3-4 Setup Delay Monitor Video Delay Sync DelayInternal Signal Blanking Width P138 E 3-4 Setup Audio Output Phase P1 Audio Output Phase P2Audio Output Phase P3 Internal Audio Signal40 E 3-4 Setup SS LIP Sync AdjustSS Audio Muting SS Normal Play SpeedSystem Time Settings Expansion Menu OperationSuperimposed Character Information Character adjustmentDisplayed information Additional information displayed in the BVE mode BVE mode display is shown below Switch Settings Preparations for RecordingSelecting the Video Signals Selecting the Audio SignalsSelecting the video signals to be monitored Selecting the audio signals to be monitoredAdjusting Recording Levels To adjust the recording levelUsing the emphasis function Recording Analog AudioPreparations for Playback DisplayedSelecting the Playback Port to be Controlled Selecting the Displayed Time DataTo display time data To display user bitsTo adjust the playback level manually Adjusting Playback Audio LevelsRemotely Controlling Video Processor Changing the Motion Mode Basic Operation with SS ModeMotion Modes Changing the Operation Mode Basic Operation with Panel ModeRecording Operation Playback OperationEE Signal Selection Initial Setup for DTR+Panel and DTR+DTR ModesSetting the Recording Time from the DTR Basic Operations with DTR+Panel and DTR+DTR ModesBasic Operations DTR+Panel and DTR+DTR Modes Port Configuration Basic Operations in BVE ModeBasic Operation of the RP Port When performing the operation through the MAVE-F555 Loading a New File for Editing in the RP PortLinear Editing through the RP Port Manual Recording through the RP PortBasic Operation of the R2 Port Basic Operation of the P2 and P3 PortsCollecting through the R2 Port Replacing Files through the R2 PortWhen the R1 key was pressed New File NamesMonitoring the RP Port Playback through the P2 and P3 PortsFile Backup Function Editing-Related Error MessagesWhen the P1 key was pressed Pre-roll Time10 E 5-5 Basic Operations in BVE Mode Error Messages ErrorRAID Com. Error RAID ErrorFM Battery Warning Fan1 TroubleRAID Battery Warning HDD xx SPC ErrorEM Mixer Config Fail Temperature RiseSpecifications GeneralOperation Digital video systemProcessor adjustment ranges Input connectorsOutput connectors Video systemRemote connectors Supplied accessoriesOptional accessories Memory Card sold separatelyPage Sony Corporation
Top Page Image Contents