PLUS Vision M-5 user manual Clearing the built-in Memory, Scrolling the Sheet

Page 25
FEED/STOP
POWER
The diagrams used in the explanations below show the copyboard installed in the horizontal position.

Clearing the built-in Memory

Use this procedure to clear all the image files in the built-in memory.

Note: The procedure described below clears all the image files in the built-in memory. Be sure to store important images on a CF memory card or computer before the operation.

Press the CLEAR button and hold it in for more 3 seconds.

Once the CLEAR button has been held in for more 3 seconds, the MEMORY indicator blinks slowly and file clearing starts.

When an error with the memory clearing has occurred and the indicator changes to the error blinking pattern, start over.

CLEAR POSITION

Scrolling the Sheet

Press the FEED/STOP button when you have used up the surface of the sheet and want to move to another surface to draw, or when you adjust the sheet position from which scanning is to start. The sheet can also be scrolled in the standby mode.

 Scrolling the sheet automatically

Press the FEED/STOP button.

The sheet scrolls one sheet’s worth to the left (or upwards).

• To stop in the middle, press the FEED/STOP button again.

Scrolling the sheet manually

The sheet can be scrolled even if the copyboard’s power is turned off. Move the sheet using your palm. The sheet moves either right or left (up or down *1). Place your palm at the center in the vertical (or hori- zontal *1) direction and move the sheet gently.

(*1 When the copyboard is installed in the vertical position.)

Note: Moving the sheet too abruptly may damage the copyboard’s drive mechanism.

Vertical/Horizontal Position Setting

The direction in which images are stored differs according to whether the copyboard is installed in the vertical or horizontal position. (The position setting is set to horizontal upon shipment from the factory.)

1.Prepare a tool to press the button in the pin hole, for example a paper clip that has been bent out, etc.

2.Check that the POWER indicator is lit. If it is off, press the POWER but- ton.

3.Stick the paper clip, etc., into the POSITION hole on the control panel and press.

The MEMORY indicator blinks slowly for 5 seconds, and the position setting is switched to vertical.

To switch back to horizontal, press the POSITION button again.

The POWER indicator blinks slowly for 5 seconds, and the position setting is switched back to horizontal.

The setting switches between vertical and horizontal each time the button in the pin hole is pressed.

 

 

 

 

E

R

 

 

W

 

 

O

 

 

P

 

 

 

 

 

 

 

 

 

 

 

 

A

R

 

 

E

 

 

 

L

 

 

 

C

 

 

 

 

 

 

 

 

 

POSITION

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Copyboard M-5 Trademarks Table of Contents Important Safety Information Care and Cleaning Packaged Contents Front and top Names of PartsBack and bottom Installation Assembly Instructions Types of Installation Read This Before InstallingOn a wall horizontal or vertical On a stand horizontal or verticalInstallation Installing on a WallSelecting the place of installation On the copyboardFix the wall mount bar to the wall surface and posts Material of wall Method of installation WoodAttach the marker tray to the Copyboard Concrete U-plugsM412 screws Upper bracket Assembly and installation flow Installing on a StandMount the two crossbars onto the T-shaped Legs assembled in 1 aboveMount the upper and lower brackets using M4 Screws Assembling Mounting Changing Brackets Copyboard Assembling the stand and mounting the copyboard verticallyImage storing On the copyboard Onto the standMount the short marker tray Mount the upper and lower brackets using M4 x 12 screwsChange the direction of image data PO- Sition to vertical Assembly and installation Installing on a Partition-PanelOn the copyboard On the partition hangers List of parts included in the partition hanger kitCatch the hooks onto partition panel Mount the copyboard on the partition panelStoring images on CF memory cards Saving and Transferring imagesEditing and printing images Applications of copyboard dataPower button When set verticallyPower indicator Green Memory indicator AmberScanning area Handling CF Memory CardsInserting CF memory cards Removing the CF memory cardPress the Power button to turn on the power Connect the AC power adapterWhen not using the copyboard Operating the CopyboardSaving the Image on the Sheet If the indicator blinks intermittently Saving sheet images in the built-in memory Press the Memory button to store that image in the memoryInsert the CF memory card into the copyboard’s card slot  Saving sheet images on a CF memory cardClearing the built-in Memory Vertical/Horizontal Position SettingScrolling the Sheet Connect the USB cable Storing Image Files on a ComputerStore the copyboard’s image folder onto the computer Open My Computer of the computerDisconnect the USB cable Deleting filesWindows 98SE Windows Me/2000/XP  Using a PC card adapter  Using a memory card reader/writer USB type Check the following before asking for repairs TroubleshootingSpecifications Start the calibration procedure Clean the sheet surfaceQuick Calibration Software Guide Software Contents and Overview Before Using the SoftwareOperating Environment Installation preparation Driver Setup Windows 98SESetup flow Click the M-5 USB DriverOpen the Device Manager screen and check the installation Uninstalling the Driver Windows 98SEUninstall the M-5 driver This completes the setupCheck whether the Copyboard is operating properly Connect the Copyboard with the personal computerWindows 98SE Disconnecting of the CopyboardWindows Me / 2000 / XP Disconnect the USB cable from the personal com- puterInstallation Setup UtilityClick M-5 Setup Utility Starting upClick Acrobat Reader Acrobat Reader InstallationClick Image Viewer Plus Image ViewerDeleting the Software Select Start → Setting→ Control PanelSelect the Remove button of the wizard and click Next 13-2127-04B

M-5 specifications

The PLUS Vision M-5 is a cutting-edge document camera and visual presenter that stands out in the educational and professional sectors. Designed with versatility and high performance in mind, this device caters to the needs of teachers, students, and business professionals alike.

One of the main features of the PLUS Vision M-5 is its high-resolution imaging capability. It offers an impressive maximum resolution of 1080p, ensuring that every detail in documents, images, or 3D objects is captured clearly and vividly. This high-definition output is critical in educational settings where clarity can significantly enhance the learning experience.

Equipped with a 16x optical zoom, the M-5 allows users to focus on intricate details without sacrificing image quality. This zoom feature is particularly beneficial for displaying small texts, intricate graphics, and technical illustrations, making it a valuable tool for subjects that require close examination such as sciences and engineering.

The M-5 also supports a range of connectivity options, including USB and HDMI outputs. This versatility allows for quick and easy connection to various devices such as laptops, projectors, and interactive whiteboards. The USB function enables simple plug-and-play usability, while HDMI ensures high-quality video output to large screens.

Another notable technology found in the PLUS Vision M-5 is its advanced image processing capabilities. It includes features like automatic focus, white balance adjustment, and image enhancement algorithms, which work together to present the best possible image quality. This technology ensures that colors are vibrant and true-to-life, making presentations and lessons more engaging.

The design of the M-5 also deserves mention. Its compact and lightweight structure makes it portable and easy to store, which is particularly advantageous for educators who frequently move between classrooms. The foldable arm design ensures convenience without compromising on the camera's functionality.

Furthermore, the PLUS Vision M-5 integrates seamlessly with interactive software applications. This compatibility allows educators to annotate and highlight documents in real-time, fostering an interactive learning environment. The ability to capture still images and videos adds another layer of functionality, enabling users to create digital content for further study or sharing.

Overall, the PLUS Vision M-5 combines high-quality imaging, versatile connectivity, and user-friendly features, making it a top choice for anyone in need of a reliable visual presenter. Whether in a classroom or a boardroom, it empowers users to deliver impactful presentations, enhance collaborative learning, and foster creativity.
Top Page Image Contents