Philips DSR2010 manual Channel Search, Default Settings, Software Upgrade

Page 40

English

11.5.4.2 Software Upgrade

This item is used for software upgrades. Select it to check the current software version as well as launch a search for new software. After a while, the Software Upgrade screen indicates whether new software is available.

-Press <EXIT> to exit the screen in case no new software is available.

In case software is available, you are offered three options:

-Press the green colour key to choose to upgrade your receiver immediately, and then press <OK> to launch new software installation.

-Or press the yellow colour key to choose to upgrade your receiver later, and then press <OK> to confirm your choice. New software installation takes place as soon as you set your receiver to stand-by.

-Or press the red colour key to refuse to upgrade your

receiver and return to the Decoder status sub menu. After successful software installation, a confirmation message is displayed. In case of installation failure, a failure message is displayed, indicating that a new installation attempt will take place as soon as you set your receiver to stand-by. In both cases, press <OK> to exit the upgrade process.

Note: you can also launch a search for new software from the screen described above using the red colour key.

11.5.5 Default Settings

This screen is used to reset your receiver back to the factory default condition.

-When prompted, press the red colour key to confirm.

-Alternatively, press <EXIT> to exit the screen without modifying the receiver settings.

Note: if you reset your receiver to default settings, you lose all the settings you stored previously.

11.6 Channel Search

This item is used to perform full satellite antenna system installation and search for new channels.

Before starting a search, configure the settings according to the following sequence:

40SETTINGS

Image 40

Contents Page Foreword ForewordQuick Installation Meaning of symbols Safety and environmental instructions Safety and Environmental InstructionsTable of Contents EPG Unpacking Product descriptionProduct Description Status indicator table Front panelRear panel U I E RInsert the smartcard with the golden chip facing up Inserting your SmartcardInserting Your Smartcard Remote Control Remote controlInserting the batteries Using the remote control RED, GREEN,YELLOW BlueConnecting your Digital-Receiver Connecting Your DIGITAL-RECEIVERConnecting to a TV and VCR both fitted with Scart sockets Connecting to a video projector to watch Digital TV Connecting to your audio equipment analogue or digitalAnalogue Connection a Digital Connection B First installation Installation settingsChannel search/Time setting First InstallationSearch failure Setting the correct time for summer or winter seasonBefore starting a new scanning Switch your receiver on or to Day-today operationLeft-hand side LED is lit in red You are watching digital TV or listening to digital radioUsing number buttons Using P+/P- buttonsUsing channel lists BannerVolume control / + Changing the current programme optionsRecording timers Electronic Programme Guide EPGSetting a timer from the EPG Setting a timer from the bannerDeleting an active timer Switching to analogue TV Viewing TeletextPremiere Features Premiere featuresPremiere Multifeed Premiere PIN code Menu tree Menu systemMenu System LNB Changing settings Cancelling/storing changesMenu navigation BasicsPremiere Service Menu Electronic Programme Guide EPGPremiere PIN-Code Change Electronic Programme Guide EPGSoftware Upgrade SmartcardSystem ScanDolby Digital out of the digital audio output DisplayChannel List Settings Timer ManagerTo delete an existing timer To set or edit a timerChannel Manager List OrganizationTo add or delete channel lists To reorder your existing channel listsTo remove channels from the selected list List EditingTo reorder channels in the selected list Channel Pool To enable Parental Lock Your PreferencesFor Parents Display optionsTV Settings Advanced settingsTo modify your password System Settings Country & Time SettingsDecoder Status System InformationSoftware Upgrade Default SettingsChannel Search LNB Configuration Antenna ConfigurationFilter Configuration Search for new channels Other settings Restoring default settingsChanging the remote control setting Advanced SettingsEasy Record to enable VCR or DVD control Connecting your equipment for Easy RecordDigital-Receiver and VCR or DVD settings Recording with the VCR control featureSymptom Cause Remedy TroubleshootingTroubleshooting Intermittent reception Faulty connections Technical specifications Technical SpecificationsEnglish