Broan WPD29M Prepare the Installation, Remove the Filters and the Grease Drip Rail

Page 5

2. PREPARE THE INSTALLATION

CAUTION

When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves.

Remove the installation kit from inside the hood.

Make sure that the following items are included:

-Wood strip (screwed on back of hood)

-Installation manual

-Transition (9’’ x 18’’ to 10’’ round)

-Accessories including:

Baffle filters (3)

Shielded halogen lights (GU10 type base, 120 V, 50 W) (4 for a 42” width hood, 6 for a 54” width hood)

Bag of parts including:

(3)waterproof wire connectors, (2) wire clamps, (4) flat head screws #10-2’’, (8) screws #8 x 5/8’’, (8) screws #8 x 3/8’’,

(2)wall anchors, (2) washers 3/16’’ ID x 3/4’’ OD

Parts sold separately:

-Interior blower Model P12D.

-In-line blower assembly ILB11, including transitions and rough-in plate. Discard the rough-in plate.

-Exterior blower assembly EB12 or EB15 (all include rough-in plate). Discard the rough-in plate.

-Duct, elbows, dampers, wall and roof caps. Refer to page 3 for a complete list of venting options and model numbers.

-Optional decorative flue AEWPD Series.

3. REMOVE THE FILTERS AND THE GREASE DRIP RAIL

A.Remove tape on filters.

Remove filters from hood and set aside. NOTE: It is recommended to start with the central one.

B.Remove tape on grease drip rail (1). Lift out grease drip rail and set aside.

NOTE: When tape is removed in the position as shown at side, drip rail will possibly fall out due to gravity.

1

HD0182

4. REMOVE THE PAN

Using a Phillips no. 2 screwdriver, remove the screws retaining the pan (shaded part on illustration beside) to the hood. Remove the pan and set aside.

RETAINING SCREWS LOCATION

HD0183

- 5 -

Image 5
Contents WPD29M Series Never Pick UP a Flaming PAN-You may be burned To Reduce the Risk of a Range TOP Grease FireOptional Decorative Flue Aewpd Series WPD29M Series Hood WPD29M Series Range Hood SystemThis unit is not designed for use with a charcoal grill Prepare the Hood Location and Select the Installation TypeRemove the PAN Prepare the InstallationRemove the Filters and the Grease Drip Rail Remove the Transition Install Wood Mounting StripConnect Wiring Install the Hood Install the TransitionInstall the Decorative Flue Optional Reinstall Grease Drip Rail and Baffle Filters Reinstall the PANBlower Cleaning Hood Cleaning Light Bulbs ReplacementUSE and Care Baffle FiltersBlower ON/OFF switch Light switchUsing hood with a covered gas grille OperationWPD29M Model Service PartsSérie WPD29M Afin DE Réduire LE Risque DE FEU DE Cuisinière AvertissementModèle P12D Système DE Hotte DE Cuisinière Série WPD29MAvertissement Retirer LE Cadre Intérieur Préparer L’INSTALLATIONRetirer LES Filtres ET LA Gouttière Choisir L’OPTION Ventilateur Extérieur OU Intérieur Installer LA Lisière DE BoisRetirer LA Transition NE PAS Réutiliser Branchement ÉlectriqueInstaller LA Hotte Installer LA TransitionInstaller LA Cheminée Décorative Optionnelle Remettre EN Place LE Cadre Intérieur 14. Réinstaller LA Gouttière ET LES FiltresEntretien Remplacement DES Lampes HalogènesFonctionnement Commande de vitesse du ventilateurInterrupteur de l’éclairage Interrupteur Marche/Arrêt du ventilateurModèle WPD29M Pièces DE RechangeSerie WPD29M Advertencia Campanas DE Cocina DE LA Serie WPD29M Modelo ILB11 AdvertenciaDesmontaje DE LA Placa Preparación DE LA InstalaciónDesmontaje DE LOS Filtros Y DEL Riel DE Vertido DE LA Grasa Selección DEL Tipo DE Ventilador Exterior O Interior Desmontaje DEL Cambio DE SecciónInstalación DE LA Regleta DE Madera Conexión DE LOS Hilos Instalación DE LA Chimenea Decorativa Instalación DEL Cambio DE SecciónInstalación DE LA Campana Instalación DEL Ventilador Ventilador Interior ÚnicamenteReinstalación DE LA Placa USO Y Cuidado Sustitución DE LAS BombillasInterruptor de las luces FuncionamientoInterruptor de encendido y apagado del ventilador Control de la velocidad del ventiladorModelo WPD29M Piezas