Broan WPD29M installation instructions Remove the Transition, Install Wood Mounting Strip

Page 6

5. REMOVE THE TRANSITION

Using a Phillips no. 2 screwdriver, remove and discard both screws and washers retaining the transition to the hood. Remove the transition and the wood mounting strip (on back of hood) and set aside.

RETAINING SCREWS AND

WASHERS LOCATION

HD0191

6. INSTALL WOOD MOUNTING STRIP

Measure and mark a level line on wall above cooktop location for the wood mounting strip (see illustration on page 4).

Center the wood mounting strip over location. See illustration shown at side. Use #10, 2’’ flat head screws to secure the mounting strip to the drywall. Make sure to hit the wall studs.

CAUTION

Due to the weight of this hood, ensure that the wood strip is attached to every available stud, not into the drywall alone.

HD0192A

1.	Drywall	4. Wall anchor location
2. Wood mounting strip		5. Back of hood outline
3.	Flat head screw	6. Wall studs

7.SELECT BLOWER OPTION (EXTERIOR OR INTERIOR)

INTERIOR BLOWER: Follow all subsequent steps of this manual.

EXTERIOR BLOWER: Discard the exterior blower rough-in plate. Refer to instructions packed with exterior blower and follow steps 8 to 11, 13 and up of the present manual.

- 6 -

Image 6

Contents WPD29M Series To Reduce the Risk of a Range TOP Grease Fire Never Pick UP a Flaming PAN-You may be burnedWPD29M Series Range Hood System Optional Decorative Flue Aewpd Series WPD29M Series HoodPrepare the Hood Location and Select the Installation Type This unit is not designed for use with a charcoal grillPrepare the Installation Remove the Filters and the Grease Drip RailRemove the PAN Install Wood Mounting Strip Remove the TransitionConnect Wiring Install the Transition Install the Decorative Flue OptionalInstall the Hood Reinstall the PAN Reinstall Grease Drip Rail and Baffle FiltersUSE and Care Light Bulbs ReplacementBlower Cleaning Hood Cleaning Baffle FiltersUsing hood with a covered gas grille Light switchBlower ON/OFF switch OperationService Parts WPD29M ModelSérie WPD29M Avertissement Afin DE Réduire LE Risque DE FEU DE CuisinièreSystème DE Hotte DE Cuisinière Série WPD29M Modèle P12DAvertissement Préparer L’INSTALLATION Retirer LES Filtres ET LA GouttièreRetirer LE Cadre Intérieur Installer LA Lisière DE Bois Retirer LA TransitionChoisir L’OPTION Ventilateur Extérieur OU Intérieur Branchement Électrique NE PAS RéutiliserInstaller LA Transition Installer LA Cheminée Décorative OptionnelleInstaller LA Hotte 14. Réinstaller LA Gouttière ET LES Filtres Remettre EN Place LE Cadre IntérieurRemplacement DES Lampes Halogènes EntretienInterrupteur de l’éclairage Commande de vitesse du ventilateurFonctionnement Interrupteur Marche/Arrêt du ventilateurPièces DE Rechange Modèle WPD29MSerie WPD29M Advertencia Campanas DE Cocina DE LA Serie WPD29M Advertencia Modelo ILB11Preparación DE LA Instalación Desmontaje DE LOS Filtros Y DEL Riel DE Vertido DE LA GrasaDesmontaje DE LA Placa Desmontaje DEL Cambio DE Sección Instalación DE LA Regleta DE MaderaSelección DEL Tipo DE Ventilador Exterior O Interior Conexión DE LOS Hilos Instalación DE LA Campana Instalación DEL Cambio DE SecciónInstalación DE LA Chimenea Decorativa Instalación DEL Ventilador Ventilador Interior ÚnicamenteReinstalación DE LA Placa Sustitución DE LAS Bombillas USO Y CuidadoInterruptor de encendido y apagado del ventilador FuncionamientoInterruptor de las luces Control de la velocidad del ventiladorPiezas Modelo WPD29M