Yamaha RX-V496RDS owner manual Connections, Before Connecting Components

Page 11

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some components require different connection methods and have different terminal names. Refer to the instructions for each component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow	video signals (composite)	V	V
White	analog audio signals for the left channel	L	L
Red	analog audio signals for the right channel	R	R
	coaxial digital signals	C	C

PREPARATION

After completing all connections, check them again to make sure they are correct.

Connecting the	Connecting to an External	Connecting Speakers	Connecting the Power
Antenna (page 10)	Decoder (page 14)	(page 15)	Supply Cords (page 17)

(Europe model)

+	R	–	MAIN		–	L	+
									MAINS
							A
							B
							SET BEFORE POWER ON		100W MAX. TOTAL
									SWITCHED
	CENTER		R		REAR	L	MAIN A OR B : 4ΩMIN. /SPEAKER
	CENTER		R	(SURROUND)		L	A + B : 8ΩMIN. /SPEAKER
							A + B : 8ΩMIN. /SPEAKER
							CENTER	: 6ΩMIN. /SPEAKER
	+					+	REAR	: 6ΩMIN. /SPEAKER
	+					+	MAIN A OR B : 8ΩMIN. /SPEAKER
							A + B : I6ΩMIN. /SPEAKER
							CENTER	: 8ΩMIN. /SPEAKER
	–					–	REAR	: 8ΩMIN. /SPEAKER
	–					–

Connecting an Audio	Connecting a Video	IMPEDANCE SELECTOR
Component (page 12)	Component (page 13)	switch (page 17)

English

9

Image 11

Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Control Checking the Package ContentsBattery Replacement Getting StartedUsing the Remote Control Front Panel Controls and FunctionsPTY Seek Mode PRESET/TUNINGPRESET/TUNING, Edit Tuning Mode AUTO/MAN’L MonoDisplay Remote Control Speakers to Be Used Speaker SetupSpeaker Placement Connections Before Connecting ComponentsOutdoor FM antenna Connecting the AntennasIndoor FM antenna included Ground GND terminal Connecting the AM loop antennaAM loop antenna included Outdoor AM antennaPhono terminals Connecting an Audio ComponentDigital audio signal terminals Connecting a Video ComponentAudio signal terminals Video signal terminalsVideo AUX terminals on the front panel Video terminalsCenter speaker terminal Connecting SpeakersMain speaker terminals Rear speaker terminalsSpeaker cables Connecting to the Main Speakers terminalsConnecting to the Rear and Center Speakers terminals AC Outlets Switched Impedance Selector SwitchConnecting the Power Supply Cords Set BASS, Treble and Balance to the 0 position Press Test Adjusting the Speaker BalanceBefore You Start Adjusting Using the Test Tone Turn up the volumeTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select the main Playing a SourceTo select a tape or an MD source Press Speakers a or BBGV background video function When you have finished using this unitTo mute the sound Analog Switching the input modeAuto DTSEncoded with DTS Off the effect speakers On the remote controlDigital Sound Field Processor DSP Effect Selecting a DSP ProgramSound Field Program Dgtl Adventure Program Subprogram Features MovieTheater Dgtl SpectacleDolby Digital or DTS + 3 digital sound fields For Hi-Fi audio sourcesDolby Pro Logic + 2 digital sound fields Press PRESET/TUNING Edit to turn z off TuningAutomatic Tuning Manual TuningHold down Memory for about three seconds Automatic preset tuning optionsWhen automatic preset tuning is completed Stations onlyTo Recall a Preset Station Manual Preset TuningHold down PRESET/TUNING Edit for about three second Exchanging Preset StationsExample If you want to exchange preset station E1 with A5 Recall preset station E1Description of RDS Data Changing the RDS ModeReceiving RDS Stations PTY Seek Function To cancel this functionProgram types in the PTY mode Press PTY Seek Mode to set the unit in the PTY Seek modeEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteD. LFE Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputSET Menu Center SP Rear SP Main SP Bass OUT Main LVLCenter SP Description of Each ItemMIN Range Adjusting the dynamic rangeMAX Last Cntr Delay Adjusting the delay of the center soundAuto Subwoofer Delay Time and Speaker Output LevelsDelay Time Sound Output Level of the CenterAdjusting Method Setting the Sleep Timer Sleep TimerCanceling the Selected Sleep Timer Example To control Yamaha CD player Preset Remote ControlControlling the Components Connected to This Unit Display MD Description of Each ModeTAPE/MD Mode Display CD ModeDVD Menu Mode DVD/LD ModeTV Mode VCR ModeCBL/SAT Mode To use a second and third VCR Setup codesAdvanced Information Enter the code number Returning to the factory-set codesGeneral TroubleshootingSymptom Cause Remedy Be heard TunerOthers Remote controlWhen playing back a source encoded with DTS Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG VCR CableSatellite Tuner CD Player DVD PlayerLD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT