Yamaha RX-V496RDS owner manual When the adjustment is complete, press Test

Page 21

4 Adjust BALANCE on the front panel so that the sound output level of the

LR

Front panel

ADJUSTING THE SPEAKER BALANCE

right main speaker and the left main speaker is the same.

5Press TIME/LEVEL

repeatedly to select the speaker to be adjusted.

“CENTER”, “R SUR.” or “L SUR.” appears on the display.

6 Press + to raise and – to lower the level. Adjust the sound output levels of the center speaker and the rear speakers so that they become almost the same as that of the main speakers.

While adjusting, the test tone is heard from the selected speaker.

Note

•You cannot adjust the delay time while the test tone is being heard even if “DELAY” appears on the display.

7When the adjustment is complete, press TEST.

“TEST OFF” appears on the display and the test tone stops.

Note

•If “CENTER SP” in the SET MENU is set to the NONE position, the sound output level of the center speaker cannot be adjusted in step 6. The center channel sound is automatically output from the right and left main speakers.

y

•Once you have completed the adjustments, you can only adjust the overall volume level of your audio system by using VOLUME (or VOLUME (u/d)).

•If there is insufficient sound output from the center and rear speakers, you may decrease the main speaker output level by setting “MAIN LVL” in the SET MENU to “–10 dB”. (Refer to page 38 for details.)

PREPARATION

English

19

Image 21

Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Battery Replacement Checking the Package ContentsGetting Started ControlUsing the Remote Control Front Panel Controls and FunctionsPRESET/TUNING, Edit PRESET/TUNINGTuning Mode AUTO/MAN’L Mono PTY Seek ModeDisplay Remote Control Speaker Setup Speaker PlacementSpeakers to Be Used Connections Before Connecting ComponentsConnecting the Antennas Indoor FM antenna includedOutdoor FM antenna AM loop antenna included Connecting the AM loop antennaOutdoor AM antenna Ground GND terminalPhono terminals Connecting an Audio ComponentAudio signal terminals Connecting a Video ComponentVideo signal terminals Digital audio signal terminalsVideo AUX terminals on the front panel Video terminalsMain speaker terminals Connecting SpeakersRear speaker terminals Center speaker terminalConnecting to the Main Speakers terminals Connecting to the Rear and Center Speakers terminalsSpeaker cables Impedance Selector Switch Connecting the Power Supply CordsAC Outlets Switched Before You Start Adjusting Using the Test Tone Adjusting the Speaker BalanceTurn up the volume Set BASS, Treble and Balance to the 0 position Press TestTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select a tape or an MD source Playing a SourcePress Speakers a or B To select the mainWhen you have finished using this unit To mute the soundBGV background video function Auto Switching the input modeDTS AnalogEncoded with DTS Digital Sound Field Processor DSP Effect On the remote controlSelecting a DSP Program Off the effect speakersSound Field Program Theater Program Subprogram Features MovieDgtl Spectacle Dgtl AdventureFor Hi-Fi audio sources Dolby Pro Logic + 2 digital sound fieldsDolby Digital or DTS + 3 digital sound fields Automatic Tuning TuningManual Tuning Press PRESET/TUNING Edit to turn z offWhen automatic preset tuning is completed Automatic preset tuning optionsStations only Hold down Memory for about three secondsTo Recall a Preset Station Manual Preset TuningExample If you want to exchange preset station E1 with A5 Exchanging Preset StationsRecall preset station E1 Hold down PRESET/TUNING Edit for about three secondChanging the RDS Mode Receiving RDS StationsDescription of RDS Data Program types in the PTY mode To cancel this functionPress PTY Seek Mode to set the unit in the PTY Seek mode PTY Seek FunctionEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteSET Menu Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputCenter SP Rear SP Main SP Bass OUT Main LVL D. LFECenter SP Description of Each ItemRange Adjusting the dynamic range MAXMIN Cntr Delay Adjusting the delay of the center sound AutoLast Delay Time Delay Time and Speaker Output LevelsSound Output Level of the Center SubwooferAdjusting Method Sleep Timer Canceling the Selected Sleep TimerSetting the Sleep Timer Preset Remote Control Controlling the Components Connected to This UnitExample To control Yamaha CD player Description of Each Mode TAPE/MD ModeDisplay MD Display CD ModeDVD Menu Mode DVD/LD ModeVCR Mode CBL/SAT ModeTV Mode Setup codes Advanced InformationTo use a second and third VCR Enter the code number Returning to the factory-set codesTroubleshooting Symptom Cause RemedyGeneral Be heard TunerRemote control When playing back a source encoded with DTSOthers Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG Cable Satellite TunerVCR DVD Player LD PlayerCD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT