Yamaha RX-V496RDS Preset Remote Control, Controlling the Components Connected to This Unit

Page 45

PRESET REMOTE CONTROL

The provided remote control is factory set to control not only this unit but also most YAMAHA audio components connected to it.

There are eight component selector buttons. Press one of these buttons which corresponds to the component you want to control with the remote control. For example, if you press CD on the component selector, the remote control is set to the CD operation mode, allowing the CD player to be controlled by the buttons on the remote control.

AMP(TUNER)

You can perform the basic operations of this unit. Refer to page 7.

CD

The code for a YAMAHA CD player is factory set.

DVD/LD & DVD MENU

An LD player can be controlled in

the DVD/LD mode. A DVD player can be controlled in the DVD/LD and DVD MENU modes. The code for a YAMAHA DVD player is factory set. If the remote control does not operate your YAMAHA DVD player, you need to set the code number “0048”.

TAPE/MD

The code for a YAMAHA tape deck is factory set. (The code for the YAMAHA MD recorder can also be set.)

VCR

A VCR can be controlled.

TV

A TV can be controlled.

CBL/SAT

A cable TV or satellite tuner can be controlled.

Note

• The button functions on the remote control differ depending on the operation mode. Refer to the following pages for details.

Controlling the Components Connected to This Unit

■Example: To control YAMAHA CD player

5

7 2

3

4

6

5Press CD on the component selector.

6Press p.

Refer to page 45 for the CD player operation buttons.

7Adjust the volume.

ADVANCED OPERATION

1Make sure that VOLUME is set to the “ m” position.

2 Press AMP(TUNER) on the component selector.

3Turn on the power.

4 Press CD on the input selector.

If you set the remote control with the manufacturers’

codes listed from page i at the end of this

manual, you can control other brands of components. Refer to “Setup codes” on page 48 for details.

English

43

Image 45

Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Battery Replacement Checking the Package ContentsGetting Started ControlUsing the Remote Control Front Panel Controls and FunctionsPRESET/TUNING, Edit PRESET/TUNINGTuning Mode AUTO/MAN’L Mono PTY Seek ModeDisplay Remote Control Speaker Setup Speaker PlacementSpeakers to Be Used Connections Before Connecting ComponentsConnecting the Antennas Indoor FM antenna includedOutdoor FM antenna AM loop antenna included Connecting the AM loop antennaOutdoor AM antenna Ground GND terminalPhono terminals Connecting an Audio ComponentAudio signal terminals Connecting a Video ComponentVideo signal terminals Digital audio signal terminalsVideo AUX terminals on the front panel Video terminalsMain speaker terminals Connecting SpeakersRear speaker terminals Center speaker terminalConnecting to the Main Speakers terminals Connecting to the Rear and Center Speakers terminalsSpeaker cables Impedance Selector Switch Connecting the Power Supply CordsAC Outlets Switched Before You Start Adjusting Using the Test Tone Adjusting the Speaker BalanceTurn up the volume Set BASS, Treble and Balance to the 0 position Press TestTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select a tape or an MD source Playing a SourcePress Speakers a or B To select the mainWhen you have finished using this unit To mute the soundBGV background video function Auto Switching the input modeDTS AnalogEncoded with DTS Digital Sound Field Processor DSP Effect On the remote controlSelecting a DSP Program Off the effect speakersSound Field Program Theater Program Subprogram Features MovieDgtl Spectacle Dgtl AdventureFor Hi-Fi audio sources Dolby Pro Logic + 2 digital sound fieldsDolby Digital or DTS + 3 digital sound fields Automatic Tuning TuningManual Tuning Press PRESET/TUNING Edit to turn z offWhen automatic preset tuning is completed Automatic preset tuning optionsStations only Hold down Memory for about three secondsTo Recall a Preset Station Manual Preset TuningExample If you want to exchange preset station E1 with A5 Exchanging Preset StationsRecall preset station E1 Hold down PRESET/TUNING Edit for about three secondChanging the RDS Mode Receiving RDS StationsDescription of RDS Data Program types in the PTY mode To cancel this functionPress PTY Seek Mode to set the unit in the PTY Seek mode PTY Seek FunctionEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteSET Menu Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputCenter SP Rear SP Main SP Bass OUT Main LVL D. LFECenter SP Description of Each ItemRange Adjusting the dynamic range MAXMIN Cntr Delay Adjusting the delay of the center sound AutoLast Delay Time Delay Time and Speaker Output LevelsSound Output Level of the Center SubwooferAdjusting Method Sleep Timer Canceling the Selected Sleep TimerSetting the Sleep Timer Preset Remote Control Controlling the Components Connected to This UnitExample To control Yamaha CD player Description of Each Mode TAPE/MD ModeDisplay MD Display CD ModeDVD Menu Mode DVD/LD ModeVCR Mode CBL/SAT ModeTV Mode Setup codes Advanced InformationTo use a second and third VCR Enter the code number Returning to the factory-set codesTroubleshooting Symptom Cause RemedyGeneral Be heard TunerRemote control When playing back a source encoded with DTSOthers Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG Cable Satellite TunerVCR DVD Player LD PlayerCD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT