Yamaha RX-V496RDS owner manual Digital Sound Field Processor DSP Effect, Selecting a DSP Program

Page 26

DIGITAL SOUND FIELD PROCESSOR (DSP) EFFECT

Selecting a DSP Program

You can enhance your listening experience by selecting a DSP program. Refer to pages 25 to 27 for details about each

program.
–	+	–	+
2
2

3

■On the front panel

1Make sure that the effect speakers (center, rear, and subwoofer) are turned on.

2Press PROGRAM h or l

repeatedly to select the desired program.

The name of the selected program appears on the display.

DSP program name

■On the remote control

1Make sure that the effect speakers (center, rear, and subwoofer) are turned on.

2Press AMP(TUNER) on the

component selector.

3Press PRG+ or PRG–

repeatedly to select the desired program.

The name of the selected program appears on the display.

DSP program name

y

If desired, adjust the delay time and the sound output level of each speaker. (Refer to pages 40 and 41 for details.)

Notes

•You can select a DSP program for each of the input sources. Once you select a program, it is linked with the input source selected at that time. So, when you select the input source next time, the same program is automatically selected.

•When a monaural source is being played with PRO LOGIC/ Normal or PRO LOGIC/ENHANCED, no sound will be heard from the main speakers and the rear speakers. Sound can only be heard from the center speaker. However, if “CENTER SP” in the SET MENU is set to the NONE position, the center channel sound is output from the main speakers.

•When a source connected to the EXTERNAL DECODER INPUT terminals of this unit is selected, the digital sound field processor cannot be used.

Canceling the Sound Effect (turning

off the effect speakers)

Press EFFECT to cancel the sound effect and

	monitor only the main	Front panel
	monitor only the main	or
	sound.	or
	sound.
	Press EFFECT again to turn the
	sound effect back on.
		Remote control

Notes

•If the sound effect is canceled when Dolby Digital or DTS is decoding, the sounds of all channels are mixed and output from the main speakers.

•If you turn off the sound effect when Dolby Digital or DTS is decoding, it may happen that the sound is output faintly or not output normally, depending on the source. In that case, turn back on the sound effect.

24

Image 26

Contents RX-V496RDS For U.K. customers Special Instructions for U.K. ModelFeaturescontents Getting Started Checking the Package ContentsBattery Replacement ControlUsing the Remote Control Controls and Functions Front PanelTuning Mode AUTO/MAN’L Mono PRESET/TUNINGPRESET/TUNING, Edit PTY Seek ModeDisplay Remote Control Speakers to Be Used Speaker SetupSpeaker Placement Before Connecting Components ConnectionsOutdoor FM antenna Connecting the AntennasIndoor FM antenna included Outdoor AM antenna Connecting the AM loop antennaAM loop antenna included Ground GND terminalConnecting an Audio Component Phono terminalsVideo signal terminals Connecting a Video ComponentAudio signal terminals Digital audio signal terminalsVideo terminals Video AUX terminals on the front panelRear speaker terminals Connecting SpeakersMain speaker terminals Center speaker terminalSpeaker cables Connecting to the Main Speakers terminalsConnecting to the Rear and Center Speakers terminals AC Outlets Switched Impedance Selector SwitchConnecting the Power Supply Cords Turn up the volume Adjusting the Speaker BalanceBefore You Start Adjusting Using the Test Tone Set BASS, Treble and Balance to the 0 position Press TestWhen the adjustment is complete, press Test Test OFF appears on the display and the test tone stopsPress Speakers a or B Playing a SourceTo select a tape or an MD source To select the mainBGV background video function When you have finished using this unitTo mute the sound DTS Switching the input modeAuto AnalogEncoded with DTS Selecting a DSP Program On the remote controlDigital Sound Field Processor DSP Effect Off the effect speakersSound Field Program Dgtl Spectacle Program Subprogram Features MovieTheater Dgtl AdventureDolby Digital or DTS + 3 digital sound fields For Hi-Fi audio sourcesDolby Pro Logic + 2 digital sound fields Manual Tuning TuningAutomatic Tuning Press PRESET/TUNING Edit to turn z offStations only Automatic preset tuning optionsWhen automatic preset tuning is completed Hold down Memory for about three secondsManual Preset Tuning To Recall a Preset StationRecall preset station E1 Exchanging Preset StationsExample If you want to exchange preset station E1 with A5 Hold down PRESET/TUNING Edit for about three secondDescription of RDS Data Changing the RDS ModeReceiving RDS Stations Press PTY Seek Mode to set the unit in the PTY Seek mode To cancel this functionProgram types in the PTY mode PTY Seek FunctionMake sure that the EON indicator lights up on the display EON FunctionRecording a Source on TAPE, MD or Video Cassette Select the source you want to recordCenter SP Rear SP Main SP Bass OUT Main LVL Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputSET Menu D. LFEDescription of Each Item Center SPMIN Range Adjusting the dynamic rangeMAX Last Cntr Delay Adjusting the delay of the center soundAuto Sound Output Level of the Center Delay Time and Speaker Output LevelsDelay Time SubwooferAdjusting Method Setting the Sleep Timer Sleep TimerCanceling the Selected Sleep Timer Example To control Yamaha CD player Preset Remote ControlControlling the Components Connected to This Unit Display MD Description of Each ModeTAPE/MD Mode CD Mode DisplayDVD/LD Mode DVD Menu ModeTV Mode VCR ModeCBL/SAT Mode To use a second and third VCR Setup codesAdvanced Information Returning to the factory-set codes Enter the code numberGeneral TroubleshootingSymptom Cause Remedy Tuner Be heardOthers Remote controlWhen playing back a source encoded with DTS Specifications Glossary Cinema DSP Cinema DSPIndex Video components DVD/LD player, VCR and TVBSR SEG VCR CableSatellite Tuner CD Player DVD PlayerLD Player MD Recorder Tape DeckV502870-2 Quick Reference Card Amptuner TAPE/MD DVD/LDDVD Menu VCR CBL/SAT VCR Stop