Yamaha RX-V496RDS Tone controls, Bass, Treble, TAPE/MD MON / EXT. Decoder, Balance, B/C/D/E, Eon

Page 7

qTone controls

These controls are only effective for the sound from the main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise to decrease the low-frequency response. The “0” position produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise to decrease the high-frequency response. The “0” position produces a flat response.

wTAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The “TAPE/MD MONITOR” indicator lights up on the display. When you press the button next, the “TAPE/MD MONITOR” indicator goes off, “EXT. DECODER” appears on the display and you can listen to a source connected to the EXTERNAL DECODER INPUT terminals.

eBALANCE

This control is only effective for the sound from the main speakers.

Turn the control to adjust the balance of the output volume from the right and left main speakers to compensate for sound imbalance caused by the speaker location or listening room conditions.

rA/B/C/D/E

Press this button to select one of a group (A to E) of preset stations.

tPRESET/TUNING

When “ z ” appears

This button is used to select a preset station number (1 to 8). Press h to select a higher and l to select a lower preset station number.

When “ z ” goes off

This button is used for tuning. Press h to tune in to higher frequencies, and l to tune in to lower frequencies.

When this unit is in the PTY SEEK mode, press this button to select a program type.

CONTROLS AND FUNCTIONS

yPRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and switch the function between for storing a broadcasting station (preset tuning) and for tuning. This button is also used to exchange the assignment of two preset stations with each other.

uFM/AM

Press this button to switch the reception band between FM and AM.

iMEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold down this button for more than three seconds to begin automatic preset tuning.

oTUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between automatic and manual. To use the automatic tuning method, press this button so that the “AUTO” indicator lights up on the display. To use the manual tuning method, press this button so that the “AUTO” indicator goes off.

pRDS MODE/FREQ

When an RDS station is received, press this button to change the display mode among the PS mode, PTY mode, RT mode, CT mode (if the station offers those RDS data services) and/or frequency display mode in turn.

aEON

Press this button to select the desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to tune in to a radio program of that type automatically.

sPTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

dPTY SEEK START

Press this button to begin searching for a station after the desired program type has been selected in the PTY SEEK mode.

fVIDEO AUX terminals

Connect an auxiliary audio or video input source such as a camcorder to these terminals. Use INPUT SELECTOR to select the source connected to these terminals.

INTRODUCTION

English

5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Control Checking the Package ContentsBattery Replacement Getting StartedUsing the Remote Control Front Panel Controls and FunctionsPTY Seek Mode PRESET/TUNINGPRESET/TUNING, Edit Tuning Mode AUTO/MAN’L MonoDisplay Remote Control Speaker Placement Speaker SetupSpeakers to Be Used Connections Before Connecting ComponentsIndoor FM antenna included Connecting the AntennasOutdoor FM antenna Ground GND terminal Connecting the AM loop antennaAM loop antenna included Outdoor AM antennaPhono terminals Connecting an Audio ComponentDigital audio signal terminals Connecting a Video ComponentAudio signal terminals Video signal terminalsVideo AUX terminals on the front panel Video terminalsCenter speaker terminal Connecting SpeakersMain speaker terminals Rear speaker terminalsConnecting to the Rear and Center Speakers terminals Connecting to the Main Speakers terminalsSpeaker cables Connecting the Power Supply Cords Impedance Selector SwitchAC Outlets Switched Set BASS, Treble and Balance to the 0 position Press Test Adjusting the Speaker BalanceBefore You Start Adjusting Using the Test Tone Turn up the volumeTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select the main Playing a SourceTo select a tape or an MD source Press Speakers a or BTo mute the sound When you have finished using this unitBGV background video function Analog Switching the input modeAuto DTSEncoded with DTS Off the effect speakers On the remote controlDigital Sound Field Processor DSP Effect Selecting a DSP ProgramSound Field Program Dgtl Adventure Program Subprogram Features MovieTheater Dgtl SpectacleDolby Pro Logic + 2 digital sound fields For Hi-Fi audio sourcesDolby Digital or DTS + 3 digital sound fields Press PRESET/TUNING Edit to turn z off TuningAutomatic Tuning Manual TuningHold down Memory for about three seconds Automatic preset tuning optionsWhen automatic preset tuning is completed Stations onlyTo Recall a Preset Station Manual Preset TuningHold down PRESET/TUNING Edit for about three second Exchanging Preset StationsExample If you want to exchange preset station E1 with A5 Recall preset station E1Receiving RDS Stations Changing the RDS ModeDescription of RDS Data PTY Seek Function To cancel this functionProgram types in the PTY mode Press PTY Seek Mode to set the unit in the PTY Seek modeEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteD. LFE Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputSET Menu Center SP Rear SP Main SP Bass OUT Main LVLCenter SP Description of Each ItemMAX Range Adjusting the dynamic rangeMIN Auto Cntr Delay Adjusting the delay of the center soundLast Subwoofer Delay Time and Speaker Output LevelsDelay Time Sound Output Level of the CenterAdjusting Method Canceling the Selected Sleep Timer Sleep TimerSetting the Sleep Timer Controlling the Components Connected to This Unit Preset Remote ControlExample To control Yamaha CD player TAPE/MD Mode Description of Each ModeDisplay MD Display CD ModeDVD Menu Mode DVD/LD ModeCBL/SAT Mode VCR ModeTV Mode Advanced Information Setup codesTo use a second and third VCR Enter the code number Returning to the factory-set codesSymptom Cause Remedy TroubleshootingGeneral Be heard TunerWhen playing back a source encoded with DTS Remote controlOthers Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG Satellite Tuner CableVCR LD Player DVD PlayerCD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT
Top Page Image Contents