Yamaha RX-V496RDS owner manual Specifications

Page 55

SPECIFICATIONS

AUDIO SECTION

• Minimum RMS Output Power
20 Hz to 20 kHz, 0.06% THD, 8 ohms
Main L/R, Center, Rear L/R		70 W*/65 W
1 kHz, 0.09% THD, 8 ohms
Main L/R, Center, Rear L/R		80 W*/70 W
• Maximum Output Power (EIAJ)
1 kHz, 10% THD, 8 ohms		100 W
• DIN Standard Output Power
1 kHz, 0.7% THD, 4 ohms		100 W
• IEC Output Power
1 kHz, 0.06% THD, 8 ohms		70 W
• Dynamic Power (IHF)
8/6/4/2 ohms	100/120/140/160 W*, 90/110/130/150 W
• Damping Factor
20 Hz to 20 kHz, 8 ohms		60
• Frequency Response
CD etc. to MAIN L/R		20 Hz to 20 kHz, ±0.5 dB
• Total Harmonic Distortion (20 Hz to 20 kHz)
CD etc. to MAIN L/R, 1/2 power, 8 ohms		0.025%

•Signal-to-Noise Ratio (IHF-A Network) CD etc. to MAIN L/R

(150 mV, Input Shorted)	96 dB
(250 mV, Input Shorted)	100 dB
• Residual Noise..............................................................................(IHF-A Network)	150 μV
MAIN L/R	150 μV
• Input Sensitivity/Impedance
CD etc	150 mV/47 k-ohms
EXT. DECODER	150 mV/40 – 47 k-ohms
• Output Level/Impedance
REC OUT	150 mV/1.2 k-ohms
SUBWOOFER	4.0 V/1.2 k-ohms
PHONES	0.47 V/390 ohms

• Channel Separation (Vol. –30 dB)

CD etc. (Input 5.1 k-ohms Terminated, 1 kHz/10 kHz)

.....................................................................................	60 dB/45 dB
• Tone Control Characteristics
BASS: Boost/cut	±10 dB/50 Hz
TREBLE: Boost/cut	±10 dB/20 kHz
* for U.S.A. and Canada models

VIDEO SECTION

• Video Signal Type	NTSC or PAL
• Video Signal Level	1 Vp-p/75 ohms
• Signal-to-Noise Ratio	50 dB
• Monitor Out Frequency Response	5 Hz to 10 MHz, –3 dB

FM SECTION

• Tuning Range	87.5/87.50 to 107.9/108.00 MHz
• Usable Sensitivity (DIN)		0.9 μV
Mono (S/N 26 dB)
Stereo (S/N 46 dB)		28 μV
• Selectivity (two signals, 40 kHz Dev., ±300 kHz)		...................... 55 dB
• Signal-to-Noise Ratio (Mono/Stereo)
DIN		75 dB/69 dB
IHF		81 dB/75 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo		0.1/0.2%
• Stereo Separation (1 kHz)		48 dB
• Frequency Response	20 Hz to 15 kHz, ±1 dB
• Antenna Input		75 ohms, Unbalanced

AM SECTION

• Tuning Range	530/531 to 1,710/1,611 kHz
• Usable Sensitivity	300 μV/m
• Signal-to-Noise Ratio	52 dB
• Antenna	Loop antenna

GENERAL

• Power Supply
[U.S.A. and Canada models]		AC 120 V, 60 Hz
[Europe, U.K. and Singapore models]		AC 230 V, 50 Hz
[Australia model]		AC 240 V, 50 Hz
[China model]		AC 220 V, 50 Hz
[General model]	AC 110/120/220/240 V, 50/60 Hz
• Power Consumption		approx. 220 W
• AC Outlets (100 W max. total)
[U.K. and Australia models]		1 (SWITCHED)
[Other models]		2 (SWITCHED)

• Dimensions (W x H x D)

.....................	435 x 151 x 391 mm (17-1/8’’ x 5-15/16’’ x 15-3/8’’)
• Weight	10 kg (22 lbs.)
• Accessories	AM loop antenna
..........................................................................	Indoor FM antenna
.....................	75-ohm/300-ohm antenna adapter (U.K. model only)
........................	Antenna adapter (U.S.A. and Canada models only)
.................................................................................	Remote control
...........................................................................................	Batteries

Specifications are subject to change without notice.

APPENDIX

English

53

Image 55

Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Control Checking the Package ContentsBattery Replacement Getting StartedUsing the Remote Control Front Panel Controls and FunctionsPTY Seek Mode PRESET/TUNINGPRESET/TUNING, Edit Tuning Mode AUTO/MAN’L MonoDisplay Remote Control Speaker Placement Speaker SetupSpeakers to Be Used Connections Before Connecting ComponentsIndoor FM antenna included Connecting the AntennasOutdoor FM antenna Ground GND terminal Connecting the AM loop antennaAM loop antenna included Outdoor AM antennaPhono terminals Connecting an Audio ComponentDigital audio signal terminals Connecting a Video ComponentAudio signal terminals Video signal terminalsVideo AUX terminals on the front panel Video terminalsCenter speaker terminal Connecting SpeakersMain speaker terminals Rear speaker terminalsConnecting to the Rear and Center Speakers terminals Connecting to the Main Speakers terminalsSpeaker cables Connecting the Power Supply Cords Impedance Selector SwitchAC Outlets Switched Set BASS, Treble and Balance to the 0 position Press Test Adjusting the Speaker BalanceBefore You Start Adjusting Using the Test Tone Turn up the volumeTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select the main Playing a SourceTo select a tape or an MD source Press Speakers a or BTo mute the sound When you have finished using this unitBGV background video function Analog Switching the input modeAuto DTSEncoded with DTS Off the effect speakers On the remote controlDigital Sound Field Processor DSP Effect Selecting a DSP ProgramSound Field Program Dgtl Adventure Program Subprogram Features MovieTheater Dgtl SpectacleDolby Pro Logic + 2 digital sound fields For Hi-Fi audio sourcesDolby Digital or DTS + 3 digital sound fields Press PRESET/TUNING Edit to turn z off TuningAutomatic Tuning Manual TuningHold down Memory for about three seconds Automatic preset tuning optionsWhen automatic preset tuning is completed Stations onlyTo Recall a Preset Station Manual Preset TuningHold down PRESET/TUNING Edit for about three second Exchanging Preset StationsExample If you want to exchange preset station E1 with A5 Recall preset station E1Receiving RDS Stations Changing the RDS ModeDescription of RDS Data PTY Seek Function To cancel this functionProgram types in the PTY mode Press PTY Seek Mode to set the unit in the PTY Seek modeEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteD. LFE Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputSET Menu Center SP Rear SP Main SP Bass OUT Main LVLCenter SP Description of Each ItemMAX Range Adjusting the dynamic rangeMIN Auto Cntr Delay Adjusting the delay of the center soundLast Subwoofer Delay Time and Speaker Output LevelsDelay Time Sound Output Level of the CenterAdjusting Method Canceling the Selected Sleep Timer Sleep TimerSetting the Sleep Timer Controlling the Components Connected to This Unit Preset Remote ControlExample To control Yamaha CD player TAPE/MD Mode Description of Each ModeDisplay MD Display CD ModeDVD Menu Mode DVD/LD ModeCBL/SAT Mode VCR ModeTV Mode Advanced Information Setup codesTo use a second and third VCR Enter the code number Returning to the factory-set codesSymptom Cause Remedy TroubleshootingGeneral Be heard TunerWhen playing back a source encoded with DTS Remote controlOthers Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG Satellite Tuner CableVCR LD Player DVD PlayerCD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT