Yamaha RX-V496RDS owner manual Using the Remote Control

Page 5

Using the Remote Control

Remote control sensor

Within approximately 6 m (20 feet)

GETTING STARTED

	The remote control transmits a directional infrared beam. Be
	sure to aim the remote control directly at the infrared sensor
	during operation. When the sensor is covered or there is a	INTRODUCTION
	large object between the remote control and the sensor, the	INTRODUCTION
	large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to receive signals properly when it is exposed to direct sunlight or a strong artificial light (such as a fluorescent or strobe light). In this case, change the direction of the light or reposition the unit to avoid direct lighting.

Notes

•Handle the remote control with care.

•Do not spill water, tea or other liquids on the remote control.

•Do not drop the remote control.

•Do not leave or store the remote control in the following conditions:

–high humidity or temperature such as near a heater, stove or bath;

–dusty places; or

–extremely low temperature.

English

Image 5

Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Battery Replacement Checking the Package ContentsGetting Started ControlUsing the Remote Control Front Panel Controls and FunctionsPRESET/TUNING, Edit PRESET/TUNINGTuning Mode AUTO/MAN’L Mono PTY Seek ModeDisplay Remote Control Speakers to Be Used Speaker SetupSpeaker Placement Connections Before Connecting ComponentsOutdoor FM antenna Connecting the AntennasIndoor FM antenna included AM loop antenna included Connecting the AM loop antennaOutdoor AM antenna Ground GND terminalPhono terminals Connecting an Audio ComponentAudio signal terminals Connecting a Video ComponentVideo signal terminals Digital audio signal terminalsVideo AUX terminals on the front panel Video terminalsMain speaker terminals Connecting SpeakersRear speaker terminals Center speaker terminalSpeaker cables Connecting to the Main Speakers terminalsConnecting to the Rear and Center Speakers terminals AC Outlets Switched Impedance Selector SwitchConnecting the Power Supply Cords Before You Start Adjusting Using the Test Tone Adjusting the Speaker BalanceTurn up the volume Set BASS, Treble and Balance to the 0 position Press TestTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select a tape or an MD source Playing a SourcePress Speakers a or B To select the mainBGV background video function When you have finished using this unitTo mute the sound Auto Switching the input modeDTS AnalogEncoded with DTS Digital Sound Field Processor DSP Effect On the remote controlSelecting a DSP Program Off the effect speakersSound Field Program Theater Program Subprogram Features MovieDgtl Spectacle Dgtl AdventureDolby Digital or DTS + 3 digital sound fields For Hi-Fi audio sourcesDolby Pro Logic + 2 digital sound fields Automatic Tuning TuningManual Tuning Press PRESET/TUNING Edit to turn z offWhen automatic preset tuning is completed Automatic preset tuning optionsStations only Hold down Memory for about three secondsTo Recall a Preset Station Manual Preset TuningExample If you want to exchange preset station E1 with A5 Exchanging Preset StationsRecall preset station E1 Hold down PRESET/TUNING Edit for about three secondDescription of RDS Data Changing the RDS ModeReceiving RDS Stations Program types in the PTY mode To cancel this functionPress PTY Seek Mode to set the unit in the PTY Seek mode PTY Seek FunctionEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteSET Menu Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputCenter SP Rear SP Main SP Bass OUT Main LVL D. LFECenter SP Description of Each ItemMIN Range Adjusting the dynamic rangeMAX Last Cntr Delay Adjusting the delay of the center soundAuto Delay Time Delay Time and Speaker Output LevelsSound Output Level of the Center SubwooferAdjusting Method Setting the Sleep Timer Sleep TimerCanceling the Selected Sleep Timer Example To control Yamaha CD player Preset Remote ControlControlling the Components Connected to This Unit Display MD Description of Each ModeTAPE/MD Mode Display CD ModeDVD Menu Mode DVD/LD ModeTV Mode VCR ModeCBL/SAT Mode To use a second and third VCR Setup codesAdvanced Information Enter the code number Returning to the factory-set codesGeneral TroubleshootingSymptom Cause Remedy Be heard TunerOthers Remote controlWhen playing back a source encoded with DTS Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG VCR CableSatellite Tuner CD Player DVD PlayerLD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT