Yamaha RX-V496RDS owner manual Impedance Selector Switch, Connecting the Power Supply Cords

Page 19

CONNECTIONS

IMPEDANCE SELECTOR Switch

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise the unit may be damaged.

If this unit fails to turn on when STANDBY/ON is pressed, the IMPEDANCE SELECTOR switch may not be fully slide to either position. If so, slide the switch to either position fully when this unit is in the standby mode.

Select the right or left position according to the impedance of speakers in your system. Be sure to move this switch only when this unit is in the standby mode.

(Europe model)

IMPEDANCE MAINS

SELECTOR

SET BEFORE POWER ON

100W MAX. TOTAL

 

 

SWITCHED

MAIN A OR B : 4ΩMIN. /SPEAKER

 

A + B : 8ΩMIN. /SPEAKER

 

CENTER

: 6ΩMIN. /SPEAKER

 

REAR

: 6ΩMIN. /SPEAKER

 

MAIN A OR B : 8ΩMIN. /SPEAKER

 

A + B : I6ΩMIN. /SPEAKER

 

CENTER

: 8ΩMIN. /SPEAKER

 

REAR

: 8ΩMIN. /SPEAKER

 

If you use

left position

right position

 

 

 

 

 

 

 

 

 

Center

The impedance must be 6 Ω

The impedance must be 8 Ω

 

PREPARATION

speaker

or higher.

or higher.

 

 

 

 

 

 

 

 

Rear

The impedance of each

The impedance of each

 

 

speakers

speaker must be 6 Ω or

speaker must be 8 Ω or

 

 

 

higher.

higher.

 

 

 

 

 

 

 

 

If you use one pair of main

If you use one pair of main

 

 

 

speakers, the impedance of

speakers, the impedance of

 

 

 

each speaker must be 4 Ω or

each speaker must be 8 Ω or

 

 

 

higher.

higher.

 

 

Main

 

speakers

If you use two pairs of main

If you use two pairs of main

 

 

 

speakers, the impedance of

speakers, the impedance of

 

 

 

each speaker must be 8 Ω or

each speaker must be 16 Ω or

 

 

 

higher.

higher.

 

 

 

 

 

 

 

Connecting the Power Supply Cords

■AC OUTLETS (SWITCHED)

(Europe model)

MAINS

SET BEFORE POWER ON

100W MAX. TOTAL

 

 

SWITCHED

MAIN A OR B : 4ΩMIN. /SPEAKER

 

A + B : 8ΩMIN. /SPEAKER

 

CENTER

: 6ΩMIN. /SPEAKER

 

REAR

: 6ΩMIN. /SPEAKER

 

MAIN A OR B : 8ΩMIN. /SPEAKER

 

A + B : I6ΩMIN. /SPEAKER

 

CENTER

: 8ΩMIN. /SPEAKER

 

REAR

: 8ΩMIN. /SPEAKER

 

To AC outlet

SWITCHED

After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time.

Europe model

2 OUTLETS

U.K. model

1 OUTLET

Use these outlets to connect the power cords from your components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W.

English

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents RX-V496RDS Special Instructions for U.K. Model For U.K. customersFeaturescontents Control Checking the Package ContentsBattery Replacement Getting StartedUsing the Remote Control Front Panel Controls and FunctionsPTY Seek Mode PRESET/TUNINGPRESET/TUNING, Edit Tuning Mode AUTO/MAN’L MonoDisplay Remote Control Speaker Placement Speaker SetupSpeakers to Be Used Connections Before Connecting ComponentsIndoor FM antenna included Connecting the AntennasOutdoor FM antenna Ground GND terminal Connecting the AM loop antennaAM loop antenna included Outdoor AM antennaPhono terminals Connecting an Audio ComponentDigital audio signal terminals Connecting a Video ComponentAudio signal terminals Video signal terminalsVideo AUX terminals on the front panel Video terminalsCenter speaker terminal Connecting SpeakersMain speaker terminals Rear speaker terminalsConnecting to the Rear and Center Speakers terminals Connecting to the Main Speakers terminalsSpeaker cables Connecting the Power Supply Cords Impedance Selector SwitchAC Outlets Switched Set BASS, Treble and Balance to the 0 position Press Test Adjusting the Speaker BalanceBefore You Start Adjusting Using the Test Tone Turn up the volumeTest OFF appears on the display and the test tone stops When the adjustment is complete, press TestTo select the main Playing a SourceTo select a tape or an MD source Press Speakers a or BTo mute the sound When you have finished using this unitBGV background video function Analog Switching the input modeAuto DTSEncoded with DTS Off the effect speakers On the remote controlDigital Sound Field Processor DSP Effect Selecting a DSP ProgramSound Field Program Dgtl Adventure Program Subprogram Features MovieTheater Dgtl SpectacleDolby Pro Logic + 2 digital sound fields For Hi-Fi audio sourcesDolby Digital or DTS + 3 digital sound fields Press PRESET/TUNING Edit to turn z off TuningAutomatic Tuning Manual TuningHold down Memory for about three seconds Automatic preset tuning optionsWhen automatic preset tuning is completed Stations onlyTo Recall a Preset Station Manual Preset TuningHold down PRESET/TUNING Edit for about three second Exchanging Preset StationsExample If you want to exchange preset station E1 with A5 Recall preset station E1Receiving RDS Stations Changing the RDS ModeDescription of RDS Data PTY Seek Function To cancel this functionProgram types in the PTY mode Press PTY Seek Mode to set the unit in the PTY Seek modeEON Function Make sure that the EON indicator lights up on the displaySelect the source you want to record Recording a Source on TAPE, MD or Video CassetteD. LFE Range DTS LFE Cntr Delay 10.MEM. Guard 11.SAT InputSET Menu Center SP Rear SP Main SP Bass OUT Main LVLCenter SP Description of Each ItemMAX Range Adjusting the dynamic rangeMIN Auto Cntr Delay Adjusting the delay of the center soundLast Subwoofer Delay Time and Speaker Output LevelsDelay Time Sound Output Level of the CenterAdjusting Method Canceling the Selected Sleep Timer Sleep TimerSetting the Sleep Timer Controlling the Components Connected to This Unit Preset Remote ControlExample To control Yamaha CD player TAPE/MD Mode Description of Each ModeDisplay MD Display CD ModeDVD Menu Mode DVD/LD ModeCBL/SAT Mode VCR ModeTV Mode Advanced Information Setup codesTo use a second and third VCR Enter the code number Returning to the factory-set codesSymptom Cause Remedy TroubleshootingGeneral Be heard TunerWhen playing back a source encoded with DTS Remote controlOthers Specifications Cinema DSP Cinema DSP GlossaryVideo components DVD/LD player, VCR and TV IndexBSR SEG Satellite Tuner CableVCR LD Player DVD PlayerCD Player Tape Deck MD RecorderV502870-2 Amptuner TAPE/MD DVD/LD Quick Reference CardVCR Stop DVD Menu VCR CBL/SAT
Top Page Image Contents