Pelco C3412M-D manual Auto Flip, Proportional PAN

Page 50

MOTION SETTINGS

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP>

<DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION>

<POWER UP>

<LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

MOTION

AUTO FLIP

PROPORTIONAL PAN

PARK TIME (MINUTES)

PARK ACTION

SCAN SPEED (DEG/S)

PRESET FREEZE FRAME

LIMIT STOPS

<SET MANUAL STOPS> <CLEAR MANUAL STOPS> <SET SCAN STOPS> <CLEAR SCAN STOPS>

<SET AZIMUTH ZERO> <CLEAR AZIMUTH ZERO>

BACK

EXIT

REFERENCE INFORMATION

MANUAL LIMITS SET

SCAN LIMITS SET

AUTO FLIP

When the camera tilts downward and goes just beyond the vertical position, the dome rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you continue to hold the joystick in the down position. Once you let go of the joystick after the dome rotates, joystick control returns to normal operation. The auto-flip feature is useful for following a person who passes directly beneath the dome.

There are two auto flip modes:

ON (default): Auto flip mode is enabled.

OFF: Auto flip mode is disabled.

PROPORTIONAL PAN

Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given amount of joystick deflection than at wide zoom settings. This keeps the image from moving too fast on the monitor when there is a large amount of zoom.

There are three proportional pan modes:

ON (default): Enables the proportional pan mode.

OFF: Disables proportional pan mode. The pan speed will not depend on the amount of zoom.

2X: Increases the speed of the proportional pan mode to twice that used when proportional pan is set to ON.

* This setting applies only to Pressurized Spectra IV dome systems.

50	C3412M-D (12/08)

Image 50

Contents Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field AlignRepeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 1 AD-32 Preset System InstallationSwitch Settings SW2 Switch 2 CM9502 SettingSW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port SettingsDome Drive Installation SW2 Switches 6-8 Baud SettingsTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFFTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System OperationAccessing Main Menu Preset Quick Programming GuideCM9500 Endura Workstation VCD500016X LowLight Color Menu Tree Edit the Password Clock Event Dome SettingsLine Sync Presets AUX18X LowLight Day/Night Menu Tree Edit the Password Clock Line Sync Presets PatternsAlarms AUX Title Text22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Spectra Language ACK Alert Reset CameraLanguage ExitAddress SW2 1 32 PRESETS. OFF DIP Switch InformationDIP Switch Information System InformationRestore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Title Text Save and Exit Cancel and Exit Help XXX.XXCamera Dome SettingsExit Dome Settings Camera Type of LightingBack Exit Camera Advanced Settings Back ExitZoom Limit Zoom Speed LOW Light LimitIR CUT Filter Applies only to 18X, 23X, and 35X modelsAGC Limit Advanced Camera SettingsShutter Speed Back Exit Auto IrisAuto White Balance Gain B Gain Auto Sharpness Auto White BalanceVideo Level Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Auto Iris Level Auto Iris PeakSensor Scan Mode Field AlignElectronic Image Stabilization Image Enhancement LOW LUX Noise ReductionWide Dynamic Range Applies only to 23X and 35X modelsAuto Flip Proportional PANBack Exit Motion Exit Dome Settings Camera Motion Power UPPark Time Preset Freeze Frame Scan SpeedLimit Stops Azimuth Zero Back Exit Power UP Power UP Action Power UPPower UP Action Back Exit Line Sync Line Sync Phase Line SyncPresets Model Number of Stored PresetsAbcdefghij Cancel Klmnopqrst Uvwxyz Space Back Exit Presets Preset NumberLabel for Preset Preset Number C3412M-D 12/08 Edit Schedule Clear Preset Clear Camera Settings Back Exit Enable Motion DetectionPresets Preset Number Preset not Defined Edit Detection AreasMotion Detection Areas Edit Schedule Activate AUX CommandAUX Time Back Exit Patterns PatternsPatterns Zones Zones Style Window BlankingBack Exit Window Blanking SET Windows Back ExitClear Window Enable Window Reverse Clear Window Back ExitReverse Blank ALL ABOVE/BLANK ALL below Window Blank Tilt AnglesAlarms C3412M-D 12/08 Default Normally open Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text Alert RepeatActivate AUX Reset AlertACK Action Current ReadingClear Back Exit Edit the Password PasswordBack Exit Password Clock Month April DAY Clock Time Base Internal ClockHour END Date Month October DAY END TimeMonth April Week 1ST DAY Sunday Time Base Internal ClockMM/DD/YYYY END Date Month October Week Last DAY Sunday END TimeEvent Holiday Event TypeBack Exit Event Event Type Event Label Back Exit Reference InformationEvent Label Edit Event LabelBack Exit Event Event Type Event Label Edit Event Label Event Type Preset Number Back ExitEdit Event Edit Event Event Label Event Active Event TimeHoliday Clear EventList Event Month January DAY Back Exit Edit HolidayEdit Holiday Occurrence Clear Holiday List HolidaysScheduled Events Event Number Event Type Label Time Occurs HolidayCycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X Models18X Models DD4CBW1822X Models DD4C2223X Models DD4CBW23DD4CBW23-X 35X Models DD4CBW35DD4CBW35-X Page Product Warranty and Return Information