Pelco C3412M-D manual Enable Motion Detection, Edit Detection Areas, AUX Time Secs Back Exit

Page 60

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER

REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

PRESETS

PRESET NUMBER

* * * PRESET NOT DEFINED * * *

<EDIT PRESET LABEL> <EDIT PRESET SCENE> <EDIT CAMERA SETTINGS> <MOTION DETECTION>

<EDIT SCHEDULE>

<CLEAR PRESET>

<CLEAR CAMERA SETTINGS>

BACK

EXIT

REFERENCE INFORMATION AZIMUTH

ELEVATION

ZOOM RATIO

CUSTOM CAMERA SETTINGS

MOTION DETECTION

MOTION DETECTION ENABLED <EDIT DETECTION AREAS> ACTIVATE AUX

AUX TIME (SECS)

BACK

EXIT

ENABLE MOTION DETECTION

(Applies only to 23X and 35X models.)

The following are the settings for motion detection:

OFF (default): Motion detection is turned off (disabled).

ON: Motion detection is turned on (enabled).

Note: Motion detection does not work if the shutter speed is set at less than 1/60 of a second.

EDIT DETECTION AREAS

(Applies only to 23X and 35X models.)

Four motion detection areas can be defined for a preset. Use the following steps to edit motion detection areas.

1.Edit detection areas 1, 2, 3, or 4:

a.Use the joystick to position the cursor beside EDIT DETECTION AREAS.

b.Press Iris Open. The EDIT DETECTION AREAS programming window appears on the monitor.

c.Use the joystick to position the cursor beside LOCATION for DETECTION AREA 1, 2, 3, or 4.

d.Press Iris Open. The cursor moves to the right next to the number 0.

e.Move the joystick up. A blue rectangle appears in the upper left-hand corner of the screen.

f.Use the joystick to place the blue rectangle over the desired detection area.

g.Press Iris Open to make a selection.

2.Set the sensitivity of the motion detection area:

a.Position the cursor next to SENSITIVITY for DETECTION AREA 1, 2, 3, or 4.

b.Press Iris Open, the cursor moves to the right.

c.Use the joystick to select one of the following sensitivity levels:

HIGH: The sensitivity level is high.

MEDIUM (default): Average sensitivity.

LOW: The sensitivity level is low.

d.Press Iris Open to make selection.

* This setting applies only to Pressurized Spectra IV dome systems.

60	C3412M-D (12/08)

Image 60

Contents Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field AlignRepeat Ack Action Activate Aux Current Reading Reset Alert Welcome Installation Switch SettingsSW2 Switch 1 AD-32 Preset System SW2 Switch 2 CM9502 SettingSW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port SettingsDome Drive Installation SW2 Switches 6-8 Baud SettingsTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFFTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System OperationAccessing Main Menu Preset Quick Programming GuideCM9500 Endura Workstation VCD500016X LowLight Color Menu Tree Dome Settings Line Sync PresetsEdit the Password Clock Event AUX18X LowLight Day/Night Menu Tree Line Sync Presets Patterns Alarms AUXEdit the Password Clock Title Text22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas ACK Alert Reset Camera LanguageSpectra Language ExitDIP Switch Information DIP Switch InformationAddress SW2 1 32 PRESETS. OFF System InformationDisplay Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit Title Text Save and Exit Cancel and Exit Help XXX.XXDome Settings Exit Dome Settings CameraCamera Type of LightingAdvanced Settings Back Exit Zoom LimitBack Exit Camera Zoom Speed LOW Light LimitIR CUT Filter Applies only to 18X, 23X, and 35X modelsAdvanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto Sharpness Auto White BalanceDome Settings ACK Alert Reset Camera Backlight Compensation BLCVideo Level Auto Iris Level Auto Iris PeakSensor Scan Mode Field AlignElectronic Image Stabilization Image Enhancement LOW LUX Noise ReductionWide Dynamic Range Applies only to 23X and 35X modelsAuto Flip Proportional PANExit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Preset Freeze Frame Scan SpeedLimit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase Line SyncPresets Model Number of Stored PresetsBack Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Enable Motion Detection Presets Preset Number Preset not DefinedEdit Schedule Clear Preset Clear Camera Settings Back Exit Edit Detection AreasMotion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns ZonesBack Exit Patterns Zones Window Blanking Back Exit Window BlankingStyle SET Windows Back ExitEnable Window Reverse Clear Window Back Exit ReverseClear Window Blank ALL ABOVE/BLANK ALL below Window Blank Tilt AnglesAlarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Alert RepeatReset Alert ACK ActionActivate AUX Current ReadingClear Password Back Exit PasswordBack Exit Edit the Password Clock Clock Time Base Internal Clock HourMonth April DAY END Date Month October DAY END TimeTime Base Internal Clock MM/DD/YYYYMonth April Week 1ST DAY Sunday END Date Month October Week Last DAY Sunday END TimeEvent Event Type Back Exit Event Event Type Event LabelHoliday Back Exit Reference InformationEvent Label Edit Event LabelEvent Type Preset Number Back Exit Edit EventBack Exit Event Event Type Event Label Edit Event Label Edit Event Event Label Event Active Event TimeClear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit Clear Holiday List HolidaysScheduled Events Event Number Event Type Label Time Occurs HolidayReset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X Models18X Models DD4CBW1822X Models DD4C2223X Models DD4CBW23DD4CBW23-X 35X Models DD4CBW35DD4CBW35-X Page Product Warranty and Return Information