Pelco C3412M-D manual ACK Action, Activate AUX, Current Reading, Reset Alert

Page 74

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP>

<DOME SETTINGS> ACK ALERT

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>

<CLEAR>

<PASSWORD>

<CLOCK>

<EVENT>

BACK

EXIT

ALERT

REPEAT ACK ACTION ACTIVATE AUX <CURRENT READING> RESET ALERT

BACK

EXIT

CURRENT READING

TEMPERATURE

DEWPOINT

PRESSURE

REFRESH

BACK

EXIT

ACK ACTION

Set ACK ACTION to program the frequency at which an alert message is displayed after the alert condition has been acknowledged. The following settings are available:

ALWAYS ON: The alert message is displayed until alert conditions are cleared.

OFF 8 HRS: The alert message is turned off for 8 hours. Message returns after 8 hours if the alert condition persists.

OFF 24 HRS: The alert message is turned off for 24 hours. Message returns after 24 hours if the alert condition persists.

OFF 48 HRS: The alert message is turned off for 48 hours. Message returns after 48 hours if the alert condition persists.

ACTIVATE AUX

This setting activates an auxiliary when an alert condition exists. Settings include the following options:

NONE (default): Not activated.

1:An alert condition will close AUX 1.

2:An alert condition will close AUX 2.

CURRENT READING

The Current Reading menu displays the existing status of temperature, pressure, and dew point inside the dome system. An arrow displayed to the left of a menu item denotes that an alert condition exists.

An up arrow indicates the reading is over the threshold. A down arrow indicates the reading is below the threshold.

The high temperature alert occurs if the temperature is above 140°F (60°C).

The low temperature alert occurs if the temperature is below -40°F (-40°C).

The high pressure alert occurs if the pressure is above 13 PSIG.

The low pressure alert occurs if the pressure is below 1 PSIG.

The dew point (high humidity) alert occurs if the difference between the temperature and the dew point is less than or equal to 3°C.

Note: The normal operating temperature inside the unit will be greater than the temperature outside the back box due to the heat emitted by the system’s electronics.

RESET ALERT

Reset alert clears the alert condition and removes the alert label from the monitor. The system automatically checks internal conditions 60 seconds after reset. If conditions are still unacceptable, the alert label reappears on the screen indicating further corrective action is required.

74

C3412M-D (12/08)

Image 74
Contents Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field AlignRepeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 1 AD-32 Preset System InstallationSwitch Settings SW2 Switch 2 CM9502 SettingSW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port SettingsDome Drive Installation SW2 Switches 6-8 Baud SettingsTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFFTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System OperationAccessing Main Menu Preset Quick Programming GuideCM9500 Endura Workstation VCD500016X LowLight Color Menu Tree Edit the Password Clock Event Dome SettingsLine Sync Presets AUX18X LowLight Day/Night Menu Tree Edit the Password Clock Line Sync Presets PatternsAlarms AUX Title Text22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Spectra Language ACK Alert Reset CameraLanguage ExitAddress SW2 1 32 PRESETS. OFF DIP Switch InformationDIP Switch Information System InformationRestore Factory Defaults Back Exit Display SetupExit Display Setup Preset Label Title Text Save and Exit Cancel and Exit Help XXX.XXCamera Dome SettingsExit Dome Settings Camera Type of LightingBack Exit Camera Advanced Settings Back ExitZoom Limit Zoom Speed LOW Light LimitIR CUT Filter Applies only to 18X, 23X, and 35X modelsAGC Limit Advanced Camera SettingsShutter Speed Back Exit Auto IrisAuto White Balance Gain B Gain Auto Sharpness Auto White BalanceVideo Level Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Auto Iris Level Auto Iris PeakSensor Scan Mode Field AlignElectronic Image Stabilization Image Enhancement LOW LUX Noise ReductionWide Dynamic Range Applies only to 23X and 35X modelsAuto Flip Proportional PANBack Exit Motion Exit Dome Settings Camera Motion Power UPPark Time Preset Freeze Frame Scan SpeedLimit Stops Azimuth Zero Back Exit Power UP Power UP Action Power UPPower UP Action Back Exit Line Sync Line Sync Phase Line SyncPresets Model Number of Stored PresetsAbcdefghij Cancel Klmnopqrst Uvwxyz Space Back Exit Presets Preset NumberLabel for Preset Preset Number C3412M-D 12/08 Edit Schedule Clear Preset Clear Camera Settings Back Exit Enable Motion DetectionPresets Preset Number Preset not Defined Edit Detection AreasMotion Detection Areas Edit Schedule Activate AUX CommandAUX Time Back Exit Patterns PatternsPatterns Zones Zones Style Window BlankingBack Exit Window Blanking SET Windows Back ExitClear Window Enable Window Reverse Clear Window Back ExitReverse Blank ALL ABOVE/BLANK ALL below Window Blank Tilt AnglesAlarms C3412M-D 12/08 Default Normally open Dwell Time Secs Edit Schedule Back Exit Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 ModeAUX Edit Title Text Title TextBack Exit Title Text Alert RepeatActivate AUX Reset AlertACK Action Current ReadingClear Back Exit Edit the Password PasswordBack Exit Password Clock Month April DAY Clock Time Base Internal ClockHour END Date Month October DAY END TimeMonth April Week 1ST DAY Sunday Time Base Internal ClockMM/DD/YYYY END Date Month October Week Last DAY Sunday END TimeEvent Holiday Event TypeBack Exit Event Event Type Event Label Back Exit Reference InformationEvent Label Edit Event LabelBack Exit Event Event Type Event Label Edit Event Label Event Type Preset Number Back ExitEdit Event Edit Event Event Label Event Active Event TimeHoliday Clear EventList Event Month January DAY Back Exit Edit HolidayEdit Holiday Occurrence Clear Holiday List HolidaysScheduled Events Event Number Event Type Label Time Occurs HolidayCycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X Models18X Models DD4CBW1822X Models DD4C2223X Models DD4CBW23DD4CBW23-X 35X Models DD4CBW35DD4CBW35-X Page Product Warranty and Return Information