Pelco C3412M-D manual Enable Window Reverse Clear Window Back Exit

Page 66

SPECTRA IV

LANGUAGE

<SYSTEM INFORMATION> <DISPLAY SETUP> <DOME SETTINGS>

ACK ALERT*

RESET CAMERA

CYCLE CAMERA POWER REBOOT SYSTEM

EXIT

DOME SETTINGS

<CAMERA>

<MOTION> <POWER UP> <LINE SYNC> <PRESETS> <PATTERNS> <ZONES>

<WINDOW BLANKING> <ALARMS>

<AUX>

<TITLE TEXT> <ALERT>* <CLEAR> <PASSWORD> <CLOCK> <EVENT>

BACK

EXIT

WINDOW BLANKING

STYLE

BLANK ALL ABOVE

BLANK ALL BELOW

<SET WINDOWS>

BACK

EXIT

SET WINDOWS

WINDOW NUMBER

<EDIT WINDOW LOCATION> <EDIT WINDOW ZOOM> <EDIT SCHEDULE>

ENABLE WINDOW

REVERSE

CLEAR WINDOW

BACK

EXIT

6.The blanked area can be programmed to turn on or off at a specified zoom point. To set the zoom point:

a.Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then press Iris Open.

b.Zoom in to the point where you want window blanking to turn on. Press Iris Open to set the zoom point.

Notes:

Since the area is already blanked out, it may be difficult to determine when you want window blanking to turn on. Reverse the window before setting the zoom point. When finished reverse the window again to blank out the area.

Increase the size of the window if any part of the blanked area is revealed during PTZ operations.

Window Blanking Disabled

Window Blanking Enabled

EDIT SCHEDULE

The Edit Schedule menu is a duplicate of the Edit Event menu (refer to Event on page 80) with the following exceptions. In the Edit Schedule menu, the event type cannot be changed. Also, the Holiday feature cannot be accessed from the Edit Schedule menu.

For instructions on changing the features in the Edit Schedule menu, refer to Edit Event on page 83.

REVERSE

A blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the blanking area remain visible. Reversing the window a second time will return it to its original condition.

CLEAR WINDOW

All areas that have been set for window blanking are cleared.

* This setting applies only to Pressurized Spectra IV dome systems.

66

C3412M-D (12/08)

Image 66
Contents Spectra IV and Spectra IV SE Series Page Contents Wide Dynamic Range Field AlignRepeat Ack Action Activate Aux Current Reading Reset Alert Welcome SW2 Switch 1 AD-32 Preset System InstallationSwitch Settings SW2 Switch 2 CM9502 SettingSW2 Switch 3 Control System Compatibility SW2 Switches 4-5 Serial Port SettingsDome Drive Installation SW2 Switches 6-8 Baud SettingsTable A. Switch Settings for SW1 P-Type Control Table B. Switch Settings for SW1 D-Type Control OFFTable B. Switch Settings for SW1 D-Type Control 100 106 141 176 211 246 Getting Started How to Operate Your Dome System OperationAccessing Main Menu Preset Quick Programming GuideCM9500 Endura Workstation VCD500016X LowLight Color Menu Tree Edit the Password Clock Event Dome SettingsLine Sync Presets AUX18X LowLight Day/Night Menu Tree Edit the Password Clock Line Sync Presets PatternsAlarms AUX Title Text22X EXview LowLight Color Menu Tree Alarms Alarm Settings Line Sync23X LowLight Day/Night Menu Tree Edit Detection Areas Patterns 35X LowLight Day/Night Menu Tree Edit Detection Areas Spectra Language ACK Alert Reset CameraLanguage ExitAddress SW2 1 32 PRESETS. OFF DIP Switch InformationDIP Switch Information System InformationDisplay Setup Exit Display Setup Preset LabelRestore Factory Defaults Back Exit Title Text Save and Exit Cancel and Exit Help XXX.XXCamera Dome SettingsExit Dome Settings Camera Type of LightingAdvanced Settings Back Exit Zoom LimitBack Exit Camera Zoom Speed LOW Light LimitIR CUT Filter Applies only to 18X, 23X, and 35X modelsAdvanced Camera Settings Shutter SpeedAGC Limit Auto Iris Auto White Balance Gain B GainBack Exit Auto Sharpness Auto White BalanceVideo Level Dome Settings ACK Alert Reset CameraBacklight Compensation BLC Auto Iris Level Auto Iris PeakSensor Scan Mode Field AlignElectronic Image Stabilization Image Enhancement LOW LUX Noise ReductionWide Dynamic Range Applies only to 23X and 35X modelsAuto Flip Proportional PANExit Dome Settings Camera Motion Power UP Park TimeBack Exit Motion Preset Freeze Frame Scan SpeedLimit Stops Azimuth Zero Power UP Power UP ActionBack Exit Power UP Power UP Action Back Exit Line Sync Line Sync Phase Line SyncPresets Model Number of Stored PresetsBack Exit Presets Preset Number Label for Preset Preset NumberAbcdefghij Cancel Klmnopqrst Uvwxyz Space C3412M-D 12/08 Edit Schedule Clear Preset Clear Camera Settings Back Exit Enable Motion DetectionPresets Preset Number Preset not Defined Edit Detection AreasMotion Detection Areas Activate AUX Command AUX TimeEdit Schedule Patterns Patterns Zones Back Exit Patterns Zones Style Window BlankingBack Exit Window Blanking SET Windows Back ExitEnable Window Reverse Clear Window Back Exit ReverseClear Window Blank ALL ABOVE/BLANK ALL below Window Blank Tilt AnglesAlarms C3412M-D 12/08 Default Normally open Back Exit AUX AUX 1 Mode Toggle Dwell Time Secs AUX 2 Mode AUXDwell Time Secs Edit Schedule Back Exit Title Text Back Exit Title TextEdit Title Text Alert RepeatActivate AUX Reset AlertACK Action Current ReadingClear Password Back Exit PasswordBack Exit Edit the Password Clock Month April DAY Clock Time Base Internal ClockHour END Date Month October DAY END TimeMonth April Week 1ST DAY Sunday Time Base Internal ClockMM/DD/YYYY END Date Month October Week Last DAY Sunday END TimeEvent Holiday Event TypeBack Exit Event Event Type Event Label Back Exit Reference InformationEvent Label Edit Event LabelBack Exit Event Event Type Event Label Edit Event Label Event Type Preset Number Back ExitEdit Event Edit Event Event Label Event Active Event TimeClear Event List EventHoliday Edit Holiday Edit Holiday OccurrenceMonth January DAY Back Exit Clear Holiday List HolidaysScheduled Events Event Number Event Type Label Time Occurs HolidayCycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Suggested Preventative Maintenance Specifications 16X Models18X Models DD4CBW1822X Models DD4C2223X Models DD4CBW23DD4CBW23-X 35X Models DD4CBW35DD4CBW35-X Page Product Warranty and Return Information