Philips Video Camera manual Language Setup, Home Function Setup

Page 26

3.13 Dome Setup (Ninth Item of Main menu)

CONFIGURATION MENU

LANGUAGE SETUP

HOME FUNCTION SETUP

OSD DISPLAY

VIEW ANGLE SETUP

INITIALIZE DATA

ORIGIN OFFSET

DOME RESET

SYSTEM INFORMATION

EXIT (ESC TO EXIT)

• LANGUAGE SETUP

LANGUAGE SETUP

LANGUAGE: ENGLISH

SAVE AND EXIT (ESC TO EXIT)

LANGUAGE : Select the language you want. * This setup displays more than 3.0 of the ROM version.

• HOME FUNCTION SETUP

After a dome control menu item has been selected, follow the directions below to set the function.

HOME FUNCTION SETUP

HOME FUNCTION

: NONE

FUNCTION NUMBER

: ---

WATING TIME

: 120SEC

FUNCTION ENABLE

: OFF

SAVE AND EXIT (ESC TO CANCEL)

HOME FUNCTION :

NONE / PRESET / TOUR / PATTERN / AUTO SCAN

FUNCTION NUMBER :

xxx

WAITING TIME :

10~240 Seconds

FUNCTION ENABLE :

ON / OFF

The Home function can be set so that the camera automatically goes to Preset, Tour, Pattern, Auto Scan after the keyboard controller has been idle for a amount of time. For example, if the Joystick controller is idle for 10 seconds, the camera goes to preset 1.

Follow these steps to program the Home position:

1.Press Menu to display the main menu on the monitor.

2.Select Home Function by pushing the Joystick to the right or to the left to scroll through the None, Tour, Pattern, Auto Scan and Preset functions.

3.Select Function Number by pushing the Joystick down, and push the Joystick to the right or to the left. The executable function number will scroll. Each function has maximum numbers. For example, you can have 240 Presets, 8 Tours, 4 Patterns and 8 Auto Scan options.

4.Select Function Time by pushing the Joystick down. Push the Joystick to the right or to the left to select from 10 to 240 seconds.

5.Select Function Enable by pushing the Joystick down. Turn the Home Enable ON or OFF by pushing the Joystick to the right or to the left.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Installation and Operating Manual Contents Safety Instructions Introduction 1.1 FeaturesPush Bubble ring ass’y Screw Remove window Assemble bubble ring ass’yInstallation and Configuration 2.1 Package Contents Different version will not support alarm input and outputBNC Basic Configuration of Fastrax II Dome Camera SystemSTP AWG #24 BNC BNC Single Multiplexer24VAC 1st Multiplexer Single User with Two Multiplexer1st Main Monitor Spot Monitor Pin NoTwo Multiplexer with Slave Keyboard Controller Two Multiplexer with Slave Keyboard Controller method Two Multiplexer with Slave Keyboard Controller methodSetting Unit for Termination SW1Dome ID Setting Address ID of Dome CameraBeyond ID 999, contact your service provider Protocol Setting Protocol of Dome CameraOff Function CameraGetting Started Alarm Display RAM Test Check NO. OK Check Aaaa OKConnection TitleMenu Accessing On-Screen Menu UtilityHow to control On-Screen Menu Utility ESCEND Angle Auto Scan SetupScan AUTOSCAN01 Quick moveFollow steps below to store the Preset positions Preset SetupJOY-LEFT to PREV. Save and Exitesc to Cancel AUTO/ ManualScan Type Normal Shortcut of Preset ProgramGuard Tour Setup DwellPattern Setup Title Follow steps below to program the PatternTitle Start END ACB Area Title SetupPRS ==== Digital Zoom SharpnessBack Light Not at EDC-142E1WB white balance Control EDC-143EAE Control Local Control Line Lock ControlMode Exit ESC to ExitFollow these steps to program the Home position Language SetupHome Function Setup View Direction View Angle SetupOSD Display Dome OSD DisplayTilt Over Angle Panning RangeFlip Initialize DataProblem Possible Solution TroubleshootingDome Reset System InformationGlossary WDRShort Cut Key Specifications EDPRemote control Alarm processingAlarm inputs BackupDimensional Drawings
Top Page Image Contents