Command No. |
|
|
|
|
|
|
| Command Description |
| ||||
|
| [Camera function mode 4] Initial data: MOD4[7..0] = 60H |
|
| |||||||||
13H: |
| Sets the camera function mode. |
|
|
|
|
|
|
| ||||
MOD4[7..0] |
| D[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
|
|
|
|
|
| D7: |
| No Function |
|
|
|
|
|
| Always set as “0” |
| |
|
| D6: |
| Trigger signal mask during exposure |
|
| 0: OFF (No mask) | 1: ON (Mask) | |||||
|
| D5 |
| Trigger signal mask during image output | 0: OFF (No mask) | 1: ON (Mask) | |||||||
|
| D4 to D0: | No Function |
|
|
|
|
|
| Always set as “100000” | |||
|
| Note 1: The trigger signal is invalidated when mask function is on. |
| ||||||||||
|
|
|
|
| |||||||||
|
| [Software Trigger Setting] Initial data: SOFTRG[7..0] = 80H |
|
| |||||||||
16H: |
| Sets the source of the software trigger. |
|
|
|
|
|
| |||||
SOFTRG[7..0] |
| D[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| D7 to D6: | Software trigger source selection |
| 00: Programming software trigger | ||||||||
|
|
|
|
|
|
|
|
|
| 10: Command software trigger | |||
|
|
|
|
|
|
|
|
|
|
|
| (200 useconds pulse width trigger signal) | |
|
|
|
|
|
|
|
|
|
| 01, 11: No function |
| ||
|
|
|
|
|
|
|
|
|
|
|
| (Prohibited settings. Do not set these values) | |
|
| D5 to D1: | No Function |
|
|
|
| Always set as “00000” |
| ||||
|
| D0: |
| Generate software trigger command | 0: Hold (Low State) 1: Generate command software trigger | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| (200 useconds high state) |
|
| Note 1: The software trigger source selection is enabled whenever “Trigger signal type | |||||||||||
|
|
| trigger (set as 0) |
|
|
|
|
|
|
|
| ||
|
| Note 2: The “Programming software trigger” is used to set up the pulse duration, trigger signal interval and generate | |||||||||||
|
|
| the trigger signal. |
|
|
|
|
|
|
|
| ||
|
| Note 3: When selecting “Command software trigger”, it is necessary to generate the software trigger signal with the | |||||||||||
|
|
| “Generate command software trigger |
| |||||||||
|
|
|
|
| |||||||||
|
| [Image Data Reset] Initial data: IMAGEREST[7..0] = 00H |
|
| |||||||||
17H: |
| Reset the Image data (FVAL, LVAL and the image data). |
|
| |||||||||
IMAGEREST |
| Change from the reset to the image data out after starting the image acquisition. |
| ||||||||||
[7..0] |
| The image data is not output when resetting the image data. |
| ||||||||||
|
| D[7..0] |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| D7 | D6 | D5 | D4 | D3 | D2 | D1 | D0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| D7 to D1: | No Function |
| Always set as “0000000” |
| |||||||
|
| D0: |
| Image Data Reset | 0: FVAL/LVAL/Image data reset |
| |||||||
|
|
| (FVAL, LVAL and the image data are low state data) | ||||||||||
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
| 1: FVAL/LVAL/Image data out |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 26/38 | |
User’s Guide Rev. 1.02 | ||
|