Ricoh FV-G200B1 manual DC Iris Lens Connector, Power-I/O Connector

Page 4

1.2DC Iris Lens Connector

M1951 (EMUDEN) or equivalent.

Pin Assignment

Pin No.	Signal Name
1	DAMP-

2	DAMP+
3	DRIVE+

4	DRIVE-

1.3Power-I/O Connector

34

1 2

HR10A-7R-6PB（Hirose）or equivalent

This connector is for the power supply (12Vdc) and input /output signals.

Use HR10A-7P-6S (Hirose) or equivalent for the cable side.

Pin Assignment

Pin No.			Signal Name		IN / OUT		Voltage
1			GND		IN		0V

2			I/O-1		OUT		+3.3V LVTTL
3			I/O-2		OUT		+3.3V LVTTL

4			TRG_In-		IN		Low: Smaller than +1.0V (Opt. Isolated -)
4			TRG_In-		IN		High: +3.0 to +26.4V (Opt. Isolated +)
							High: +3.0 to +26.4V (Opt. Isolated +)
							*potential difference between TRG_In- and
5			TRG_In+		IN		*potential difference between TRG_In- and
5			TRG_In+		IN		TRG_In+
							TRG_In+

6			POWER IN		IN		+10.8 to +26.4 Vdc

Output signals can be assigned through the camera setting communication. (Device Code = 00H, Command = F0H and F1H)

IO Signal Patterns for Pin No.2 (I/O-1) and Pin No.3 (I/O-2)

	Command No.				HR10A-7R-6PB (Hirose)
F0H[3..0]	F1[3]	F0H[7..4]	F1[4]		I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
For I/O-1 (Pin No. 2)		For I/O-2 (Pin No.3)			I/O-1 (Pin No.2) / I/O-2 (Pin No.3)
For I/O-1 (Pin No. 2)		For I/O-2 (Pin No.3)
0H	-	0H	-		FrameTriggerWait
(initial setting)	-	0H	-		(initial setting for I/O-1)
(initial setting)					(initial setting for I/O-1)

1H	Set Value	1H	Set Value		UserOutput

2H	-	2H			ExposureActive
2H	-	(initial setting)			(initial setting for I/O-2)
		(initial setting)			(initial setting for I/O-2)

3H	-	3H	-		TriggerAuxiliary
4H	-	4H			TriggerInternal

5H	-	5H			SensorReadOut

6H	-	6H			StrobeSignal

7H-FH	-	7H-FH	-		For Test Use Only

	FV-G200B1	4/38
	User’s Guide Rev. 1.02	4/38
	User’s Guide Rev. 1.02

Image 4

Contents GigE Vision VGA Monochrome CCD Camera FV-G200B1 FV-G200B1 User’s Guide RevTable of Contents Connector Specifications RJ45 ConnectorDC Iris Lens Connector Power-I/O ConnectorFV-G200B1 User’s Guide Rev Equivalent Circuit for the Input Pin of the I/O Connector Or equivalent connectorHorizontal Timing Vertical Timing Full Scanning2 1/2 Partial Scanning 3 1/4 Partial ScanningAOI Area of Interest Fval Lval SUBPixel Transferring Image Pulse Width Trigger Mode Normal ModeTiming Exposure Timing with the Positive Polarity Trigger Signal Input Trigger signalTrigger signal Trigger signal With Photocoupler delayEdge Preset Trigger Mode 14/38 15/38 16/38 Reset mode Communication Method Communication SettingsCommunication Format Name Descriptions 【Example Code】Reading the data from the command 00H Camera Control Command Camera Command List Device Code22/38 23/38 24/38 Descriptions of the Camera Control Commands Device code Underline settings are the factory default settings26/38 27/38 28/38 29/38 30/38 Descriptions of the Camera Commands Device code AGC32/38 33/38 34/38 GenICam Command / Camera Command Reference Table GenICam command Device Command Function2EH 37/38 38/38