Sanyo DSR-C100 instruction manual Installing and Handling, Ni-Cd Backup Battery

Page 12

INSTALLING AND HANDLING

THE Ni-Cd BACKUP BATTERY

The Ni-Cd battery which is supplied with the camera is used as a backup power supply for the clock and the hard disk.

The battery has not been charged. Before turning on the camera power, install the battery by referring to the points below. If any problems with battery operation or leakages of battery fluid occur, contact the place of purchase.

Note:

•Once the camera's power has been turned on and left on for 24 hours, the battery will be charged sufficiently to provide 30 days of backup operation.

•If the battery is used continuously for long periods, leakage of battery fluid may occur. The interior of the battery compartment is lined with absorbent material to absorb any fluid which should happen to leak from the battery, so if replacing the battery after a leak has occurred, be sure to replace this absorbent material also.

•Always be sure to use the accessory AC adapter. If you use some other commercially-available AC adapter, detection of problems with the backup battery will not be possible, and damage to the hard disk may result.

•If the camera power supply is turned off or a power outage occurs after the battery has only been charging for a short time, it may cause the clock setting to be re-initialized. If this happens, the camera will not operate.

•Never open the rear cover while power is being supplied to the camera. Always be sure to set the hard disk to the standby condition before opening the rear cover. (See page 18)

(Warning displays)

•When the camera power is turned on after the battery has been replaced, “LOW BATT” will appear on the monitor screen, and charging of the battery will start automatically.

•Approximately 1 hour of charging time is needed before the “LOW BATT” display disappears from the monitor screen. If the “LOW BATT” display does not disappear after one hour or more has passed, it may indicate a problem with the battery.

•If “LOW BATT” appears on the monitor screen while the camera is in use, the warning indicator will flash and recording of images will be halted. This may also indicate a problem with the battery, so replace the battery at such times.

•If the battery has not been installed, or if the battery terminal contacts are not complete, “NO BATT” will appear on the monitor display. If this happens, check the battery once more.

English

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents DSR-C100 Contents Function Operations Formatting the memory cardInformation to User Declaration of ConformityPrecautions Features AccessoriesPart Names and Functions Front Panel Control terminals Indicator Monitor display Camera status OFFMonitor display Camera status Installing and Handling Ni-Cd Backup BatteryInstalling the Ni-Cd battery Hold-up switch B Suspicion switch Connecting the power supplyConnections Basic connectionsConnection to a computer RS-232C cable connectionComputer Hard Disk Hard disk recording areasProtecting the hard disk Checking the hard diskTurn on the power. See page 1 From Recording to PlaybackHard Disk Standby Mode Setting to standby modeCanceling standby mode Press the Menu buttonMemo Menu Settings BClock settings BSystem settings Menu screen displaySetting the Clock Clock SET Setting example To set the clock to 151520 on 2 AugustBefore setting System Settings System SET Hard disk initialization PaletteHard Disk Capacity Settings HDD SET Changing the alarm capacityUse the Cursor dor c button to set Mode ... on Use the Cursor l button to select Week SUNUse the Cursor l button to select Minute Summer Time Settings Summer TIME/DAYLIGHT SET KEY Word Setting KEY Word SET KEY Word SET File ID a Camera ID CommentEntering a file ID 1 character Press the SET buttonSetting a camera ID 5 characters Enter ALL1 in same wayEntering a comments up to 36 characters Example Set the password to Camera Use the Cursor jor l button to selectButton Change PASSWORD-DELETE OLD Password Setting a password for initializing the hard disk Example To change the initial setting of END to CMROLD Password For Camera ID and Comment settings For Password or Camera ID settingCorrecting characters 1Checking the Clock SET settings 2Checking the HDD SET settings3Checking the System SET settings 4Checking the Summer TIME/DAYLIGHT SET settingsSetting the Recording Method IlluminationImage quality Pre-alarm PRE1 recording Post-alarm POST-1 recordingSuspicion recording Pre-alarm recording flow Pre-alarm recording Screen displays1Display during recording 2Number of suspicion recording imagesPost-alarm recording Press and hold the H HOLD-UP switch rear panelRelease the H HOLD-UP switch to stop recording Backup recording Pre-alarm 2 PRE2 recording starts automatically
Top Page Image Contents