Sony DXC-D30WSP Connections, Using Accessories Using the Carrying Case, Connecting a Portable VTR

Page 27

DXC-D30WS/P(E)/V1

Chapter 2 Fitting and Connections

Using Accessories

Using the Carrying Case

Stowing the camera

Align the camera with the base of the case, and slide the camera in forward.

Checking that the pin at the rear engages correctly, push forward until it locks into place.

Notes

•Bring the viewfinder into the horizontal position, slide it fully rearward and to the left, then fix before stowing.

•When an optional microphone (ECM-670/672, C-74, etc.) is attached, loosen the microphone fixing screws, move the microphone to the lowest position, and fix before stowing.

Align the camera with the base of the carrying case.

Base Lever

Connections

Connecting a Portable VTR

Using the optional CA-537/537P or CA-327/327P Camera Adaptor and a camera cable, you can connect a portable VTR. Set the VTR selector switch on the camera adaptor according to the VTR connected.

If using a VTR from another manufacturer, consult your Sony dealer.

Checks before making connections

Check first that the video camera, camera adaptor, VTR, and other devices are all powered off.

Making connections

Using a camera cable, connect the VTR/CCU/CMA connector on the camera adaptor to the camera input connector of the VTR.

Video monitor

•If using an S-VHS VTR, using a video monitor with an S-video input connector and connecting it to the S- video connector of the VTR will allow you to monitor a clear picture, with no flecking.

•The output video signal from the VIDEO OUT connector of this unit is a composite video signal.

Connect the VIDEO OUT connector of this unit to a composite video signal input connector of the monitor.

Setting the VTR selector switch on the

Chapter

camera adaptor

 

2

When using the camera with a CA-537/537P/327/327P

Fitting

Camera Adaptor, it is essential to correctly set the

and

VTR selector switch on the camera adaptor according

Connections

to the VTR connected. This switch determines the

type of video signal output from the VTR/CCU/CMA

connector and the audio output signal level.

 

Example: When using a CA-537/537P

 

VTR SELECT switch

 

Example of fully-stowed carrying case

DXC-D30/D30P Color Video Camera

This can be stored with the following system component fitted.

•CA-537/537P/327/327P/325A/325AP/325B Camera Adaptor or DSR-1/1P, PVV-3/3P or EVV-9000/9000P

•DXF-701/701CE Viewfinder

•ECM-670/ECM-672/C-74 Microphone

•Zoom lens (VCL-916BYA etc.) (Largest lens which can be stowed is Canon J18 X 8.5BI-B.)

•CAC-12 Microphone Holder

•CAC-4 Chest Pad

VCT-U14 Tripod Adaptor

Fasten straps.

Cassettes, camera cables, etc.

32

Chapter 2 Fitting and Connections

LC-421 Carrying

Case

NP-1A/1B Battery Packs (maximum two) - Fasten straps.

Example: Connecting a BVW-50/50P Portable VTR to a CA-537/ 537P Camera Adaptor

CA-537/537P Camera

Adaptor

26-pin connector

VTR/CCU/CMA DXC-D30/D30P

CCZ-A Camera Cable

26-pin connector

CAMERA IN

BVW-50/50P Portable VTR

Camera cable

•Select a camera cable to fit the camera input connector on the VTR you are using.

•The maximum camera cable extent is 10 m (33 ft).

For details, consult your Sony dealer.

 

2

1

3

Chapter 2 Fitting and Connections

33

1-23

Page 26 Page 28
Image 27
Page 26 Page 28
Contents
DXC-D30WS DXC-D30WSP Varning Introducing this manual Related manuals Manual StructureTable of Contents Operating instructions Digital Video CameraTable of Contents Overview Advanced Menu Settings FeaturesAbout This Manual Battery Pack Operating Times Advanced Menu Settings Video Output and Viewfinder PictureItemSettings DXC-D30WSL/D30WSPL Camera Head SpecificationsSupplied accessories Related ProductsHorizontal resolution in 43 mode SpecificationsMeasuring Horizontal Resolution Horizontal resolution in 169 modeDXC Chart of Optional Components and AccessoriesUsing the Camcorder Grip Using Battery Packs Camera Adaptor Power SupplyCamera Head VCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Table of Contents Camera adaptor Product ConfigurationsFeatures Camera Head Location and Function of PartsLocation and Function of Parts Left and upper view Front viewVCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Location and Function of Parts To remove the VTR Using the Camcorder GripFitting a VTR Attaching a camcorder grip to the DSR-1/1P Attaching a camcorder grip to the PVV-3/3P Fitting a VTRIf using a lens with a 6-pin connector Fitting the LensFitting optional filters Using Accessories Using the ViewfinderUsing an Optional Microphone Fitting an optional microphone Using AccessoriesAdjusting the Shoulder Pad Position Fitting to a TripodUsing Accessories Using the Carrying Case Connecting a Portable VTRConnections VTR Connecting a Number of Cameras Using a Camera Control UnitConnections Connected VTRBattery low indications Power SupplyUsing Battery Packs Battery pack operating timesFilter setting Lighting conditions Basic Procedure for ShootingPower Supply Camera Adaptor Power Supply Camera with a separate power supplyReviewing the recording Basic Procedure for ShootingUsing the ClipLink Function Shooting with the DSR-1/1PShooting with the DSR-1/1P Using the Edit Search Function While Back Space EditingSetting Mark IN/OUT points as you shoot Setting cue points as you shootUsing the Freeze Mix Function Viewfinder Screen IndicationsChanging the Viewfinder Display Viewfinder Screen Indications Viewfinder Normal IndicationsViewfinder Normal Indications Basic Menu Operations Contents and Settings of EachViewfinder Basic Menu Status IndicationsSetting the recording time in seconds Setting the recording time in minutesViewfinder Basic Menu To record a title Basic menu pages 8Entering the title DSR-1/1PTo return to the normal indications Viewfinder Advanced MenuAdvanced Menu Operations To changeViewfinder Advanced Menu To set the camera ID EZ mode settingsAdvanced menu pages 9 to Advanced menu pages 13To call up files recorded onto a tape when 38Setup FilesCalling up a Setup File Using the DSR-1/1PSetup Files Changing File Settings Saving File SettingsTo save setup files to a tape when using the DSR-1/1P Using SetupNavi and SetupLog with the DSR-1/1P Setup FilesSetting up the camera Using Data Recorded on Tape To abort the data recording while in progress Using SetupNavi and SetupLog with the DSR-1/1PRecording the Menu Settings onto a Tape Viewing SetupLog DataSaving an Appropriate White Balance Value in Memory White Balance AdjustmentUsing the Preset White Balance Settings White Balance AdjustmentLight Sources and Color Temperature Using the ATW Auto Tracing White Balance FunctionCLS Clear Scan function 44Black Balance Adjustment Shutter SettingsSetting the shutter speed, CLS and EVS function Shutter speedsWhen shooting is finished Setting the Clock and Timestamping RecordingsShutter Settings How to set the date and time46Setting the Clock and Timestamping Recordings Viewfinder Screen AdjustmentsUsing the zebra pattern in manual adjustment mode Adjusting the LensFlange Focal Length Adjustment Iris AdjustmentsReducing the size of the image Settings for Special Cases48Adjusting the Lens Macrophotography Ending close-up shootingImportant Notes on Operation Settings for Special CasesAdjusting Color in the Specified Area Characteristics of CCD SensorsVCL-916BYA Zoom Lens DXC-D30/D30P Camera HeadVCL-915BYA/916BY/1012BY Zoom Lens Design and specifications are subject to changeDXF-701/701CE Viewfinder HoodVHS VTR 52Chart of Optional Components and AccessoriesBoard Layout Removal of CabinetRemoval of Side Plate Assembly Replacement of Main PartsReplacement of CCD Unit DisassemblyCN2 Connectors and Cables Connector Input/Output SignalsPin Signal Specification CAMERA/CA 76P, Male Remote 10P, Female VF 20P, Female Replacement Way of ROMIC102 HOW to Handle of AT-125 BoardConnection Connector How to Attach of the Extension Board EX-591External View Check Point Voltage Value DC-DC Converter VoltageConnection Service Mode OperationService mode Menu screenStandard set value Reset object item and standard set value for setting Table2 Standing Correction 1 Reset3 Flare Adjustment 4 Pre Knee Setting8 SC adjustment 5 Component Level Adjustment6 CLP Level Adjustment 7 Chroma/VF Adjustment12 RG, SUB communication 9 Various kinds items setting10 Test Mode 11 Head Block No. information16 Knee setting 3 not in used 13 Various items setting14 Title Color setting 15 Various items setting18 Selfdiagnosis 17 Various setting20 Selfdiagnosis 19 SelfdiagnosisRC-CCR 21 SelfdiagnosisRC-PMPD RC-CYMemory DSP COM23 TG ROM Operation 22 Present unit condition indicationPattern box PTB-500 Grayscale chartPreparation Equipment Required ConnectionSwitch Setting Before Adjustment Adjustment Item Before Adjustment Color Bar Signal ConfirmationSensitivity Measurement Confirmation 3. Y/R-Y/B-Y CLP Level Adjustment Camera AdjustmentSub-Carrier Frequency Adjustment INT SC-H Phase AdjustmentLVL UP LVL 4. Y/SYNC/R-Y/B-Y Level AdjustmentCarrier Balance Adjustment Adjusting pointTo be extended ES-22 board Preparation Chroma VBS Level AdjustmentVBS Level Adjustment → SET UP on MAT Dest SmpteYC Level Adjustment Chroma YC Level AdjustmentSpecification for Ntsc → CAM/DCC+ VF SYNC/BLKG Level AdjustmentSpecification a = 165 ±5 mV VF Sync → VF Blkg→ R Shad G Shad B Shad Pedestal AdjustmentShading Adjustment Test point Spec Mode VA-185 board→CAM/DCC+ Flare AdjustmentMIC LEVEL/MIC Level IND Adjustment Adjusting point Lens irisAdjusting point 1CV1/MB-785 board Specification Character Position AdjustmentTitle Adjustment Adjusting point 1CV3/MB-785 board SpecificationPage Sony Corporation
Top Page Image Contents