Sony DXC-D30WSP service manual Viewfinder Advanced Menu

Page 40

1-36

Viewfinder Advanced Menu

Advanced menu page 3

PAGE 3(NEXTm$ PREVm4)

mAWB MEM:2

TONE:OFF BARS:SMPTE a)

REMOTE1:REC

REMOTE2:MARK BAUD RATE:38400

EXIT MENU (YESm4)

a) For DXC-D30P: EBU75

Advanced menu page 4

PAGE 4(NEXTm$ PREVm4)

MARKER:CENT/90% mZEBRA:1

ZEBRA1:70IRE a) VF SDTL:± 0 VF TALLY:× 2

EXIT MENU (YESm4)

a) For DXC-D30P: 70%

Advanced menu page 5

Advanced menu page 6

PAGE 5(NEXTm$ PREVm4)

PAGE 6(NEXTm$ PREVm4)

mSS

IND:ALWAYS

mAUDIO

IND:ON

LL

IND:ON

TAPE

IND:ON

MIC

 

IND:ON

TC

IND:ON

IRIS

IND:ON

ID

IND:OFF

GAIN

IND:ON

ID

SET:µ

FILTER IND:ON

 

(

)

EXIT

 

MENU (YESm4)

EXIT

MENU (YESm4)

Chapter 4 Viewfinder Screen Indications and Menus

Item

Settings

AWB MEM

2 (normal value): No

Selects whether or not to

correspondence with FILTER

make the FILTER knob

knob settings. Only two

settings (1 to 4) correspond

adjustment values (A and B)

to separate white balance

are stored in memory.

adjustment values stored in

2 × 4FL: Correspondence

memory.

with FILTER knob settings.

 

Each of the four knob

 

settings can be used to set A

 

and B adjustment values, for

 

a total of eight settings.

TONE

ON (normal value): Output

Selects whether or not to

audio signal.

output a 1-kHz audio signal

OFF: Do not output audio

with the color bars when the

signal.

OUTPUT/DL/DCC+ has

 

been set to BARS.

 

BARS

SMPTE (normal value for

Selects normal width or

DXC-D30):Normal width

narrower width for color

EBU75 (normal value for

bars.

DXC-D30P): EBU 75%

 

EBU100 (for DXC-D30P):

 

EBU 100%

 

SPLIT (for DXC-D30P): Not

 

for normal operation

 

SNG: Narrower than normal

 

(used for satellite

 

communications, etc.)

REMOTE1

REC (normal value):

Sets a function for position 1

Specifies recording start/stop

of a switch connected to the

MARK: Specifies a Mark IN/

REMOTE1 connector.a)

OUT point.

 

CUE: Specifies a cue point.

 

NG: Specifies NG/OK.

REMOTE2

REC: Specifies recording

Sets a function for position 2

start/stop.

of a switch connected to the

MARK (normal value):

REMOTE1 connector.a)

Specifies a Mark IN/OUT

 

point.

 

CUE: Specifies a cue point

 

NG: Specifies NG/OK.

BAUD RATE

9600, 38400 (normal value)

Sets a baud rate for a

 

computer connected to the

 

REMOTE connector 1 (to be

 

supported in future version).

 

Item

Settings

MARKER

CENT/90% (normal value):

Selects ON/OFF setting for

Displays center marker and

center marker, size setting

safety zone marker at 90%

(percentage of viewfinder

size.

screen area), and display

CENT/80%: Displays center

ON/OFF setting.

marker and safety zone

 

marker at 80% size.

 

90%: Displays only safety

 

zone marker at 90% size.

 

80%: Displays only safety

 

zone marker at 80% size.

 

CENT: Displays only center

 

marker.

ZEBRA

1 (normal value): Displays

Selects type of zebra pattern

the zebra pattern over parts

display.

having a video level.

 

between 70 and 90 IRE (or

 

70 and 90%).

 

Use the next item (ZEBRA1)

 

to select the base level.

 

2: Displays the zebra pattern

 

over parts having video

 

levels of 100 IRE or above

 

( or 100% or above).

 

1/2: Dual display (both 1

 

and 2)

ZEBRA1

70 IRE (normal value) to 90

Sets base level for zebra

IRE or 70% (normal value)

pattern 1.

to 90%

 

Can be set for each IRE

 

step or 1% step.

VF S DTL

–99 to +0 (normal value) to

Sets the detail level of

+99

images on the viewfinder

Negative values set softer

screen (displayed only when

edges and positive values

the DXF-501/501CE/601/

set sharper edges.

601CE viewfinder is

 

attached).

 

VF TALLY

×1: Uses only the upper

Selects whether or not to use

REC/TALLY indicator.

more than one REC/TALLY

×2 (normal value): Uses

indicators in the viewfinder

two REC/TALLY indicators.

(displayed only when the

 

DXF-701/701CE viewfinder

 

is attached).

 

Item

Settings

SS IND

3SEC: Displays shutter

Selects the mode for

setting for three seconds only

showing the shutter setting

when the setting has been

when displaying the normal

changed.

indications.

ALWAYS (normal value):

 

Displays the shutter setting at

 

all times.

LL IND

ON (normal value):

Selects whether or not to

Displays.

show the LOW LIGHT

OFF: Not display.

indication on the normal

 

indications when inadequate

 

lighting is detected.

 

MIC IND

ON (normal value):

Selects whether or not to

Displays.

show the camera

OFF: Not display.

microphone output

 

indication on the normal

 

indications.

 

IRIS IND

ON (normal value):

Selects whether or not to

Displays.

show the lens’s F-stop value

OFF: Not display.

(iris indication) on the

 

normal indications. The F-

 

stop value is always

 

displayed when in EZ mode.

 

GAIN IND

ON (normal value): Always

Selects whether or not to

displays.

always show the gain

OFF: displays for two

setting indication on the

seconds only when the

normal indications.

setting has been changed.

FILTER IND

ON (normal value): Always

Selects whether or not to

displays.

always show the FILTER

OFF: Displays for two

knob setting indication on

seconds only when the

the normal indications.

setting has been changed.

The FILTER knob setting

 

indicator is always displayed

 

when in EZ mode.

 

Item

Settings

AUDIO IND

ON (normal value):

Selects whether or not to

Displays.

show the audio level

OFF: Not display.

indication on the normal

 

indications (valid only when

 

the DSR-1/1P or PVV-3/3P

 

is connected).

 

TAPE IND

ON (normal value):

Selects whether or not to

Displays.

show the VTR’s remaining

OFF: Not display.

tape indication on the normal

 

indications. (valid only when

 

the DSR-1/1P or PVV-3/3P

 

is connected).

 

TC IND

ON (normal value):

Selects whether or not to

Displays.

show the time data indication

OFF: Not display.

on the normal indications

 

(valid only when the DSR-1/

 

1P or PVV-3/3P is

 

connected).

 

ID IND

ON (normal value):

Selects whether or not to

Displays.

display the camera ID when

OFF: Not display.

displaying color bars.

 

ID SET

See “To set the camera ID”

Sets the camera ID (up to

on next page.

eight characters, including

 

alphanumerics, symbols,

 

and spaces).

 

Chapter 4 Viewfinder Screen Indications and Menus

DXC-D30WS/P(E)/V1

a)For more information about a connectable switch, contact your Sony dealer.

58 Chapter 4 Viewfinder Screen Indications and Menus

Chapter 4 Viewfinder Screen Indications and Menus 59

Page 39 Page 41
Image 40
Page 39 Page 41
Contents DXC-D30WS DXC-D30WSP Varning Manual Structure Introducing this manual Related manualsTable of Contents Digital Video Camera Operating instructionsTable of Contents Features Overview Advanced Menu SettingsAbout This Manual Advanced Menu Settings Video Output and Viewfinder Picture Battery Pack Operating TimesItemSettings Specifications Supplied accessoriesRelated Products DXC-D30WSL/D30WSPL Camera HeadSpecifications Measuring Horizontal ResolutionHorizontal resolution in 169 mode Horizontal resolution in 43 modeChart of Optional Components and Accessories DXCUsing Battery Packs Camera Adaptor Power Supply Using the Camcorder GripCamera Head VCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Table of Contents Product Configurations Camera adaptorFeatures Location and Function of Parts Camera HeadLocation and Function of Parts Front view Left and upper viewVCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Location and Function of Parts Using the Camcorder Grip Fitting a VTRAttaching a camcorder grip to the DSR-1/1P To remove the VTRFitting a VTR Attaching a camcorder grip to the PVV-3/3PFitting the Lens If using a lens with a 6-pin connectorFitting optional filters Using the Viewfinder Using AccessoriesUsing an Optional Microphone Using Accessories Adjusting the Shoulder Pad PositionFitting to a Tripod Fitting an optional microphoneConnecting a Portable VTR Using Accessories Using the Carrying CaseConnections Connecting a Number of Cameras Using a Camera Control Unit ConnectionsConnected VTR VTRPower Supply Using Battery PacksBattery pack operating times Battery low indicationsBasic Procedure for Shooting Power Supply Camera Adaptor Power SupplyCamera with a separate power supply Filter setting Lighting conditionsBasic Procedure for Shooting Using the ClipLink FunctionShooting with the DSR-1/1P Reviewing the recordingUsing the Edit Search Function While Back Space Editing Setting Mark IN/OUT points as you shootSetting cue points as you shoot Shooting with the DSR-1/1PViewfinder Screen Indications Using the Freeze Mix FunctionChanging the Viewfinder Display Viewfinder Normal Indications Viewfinder Screen IndicationsViewfinder Normal Indications Contents and Settings of Each Viewfinder Basic MenuStatus Indications Basic Menu OperationsSetting the recording time in minutes Setting the recording time in secondsViewfinder Basic Menu Basic menu pages 8 Entering the titleDSR-1/1P To record a titleViewfinder Advanced Menu Advanced Menu OperationsTo change To return to the normal indicationsViewfinder Advanced Menu EZ mode settings Advanced menu pages 9 toAdvanced menu pages 13 To set the camera ID38Setup Files Calling up a Setup FileUsing the DSR-1/1P To call up files recorded onto a tape whenSaving File Settings Setup Files Changing File SettingsTo save setup files to a tape when using the DSR-1/1P Setup Files Using SetupNavi and SetupLog with the DSR-1/1PSetting up the camera Using Data Recorded on Tape Using SetupNavi and SetupLog with the DSR-1/1P Recording the Menu Settings onto a TapeViewing SetupLog Data To abort the data recording while in progressWhite Balance Adjustment Saving an Appropriate White Balance Value in MemoryWhite Balance Adjustment Light Sources and Color TemperatureUsing the ATW Auto Tracing White Balance Function Using the Preset White Balance Settings44Black Balance Adjustment Shutter Settings Setting the shutter speed, CLS and EVS functionShutter speeds CLS Clear Scan functionSetting the Clock and Timestamping Recordings Shutter SettingsHow to set the date and time When shooting is finishedViewfinder Screen Adjustments 46Setting the Clock and Timestamping RecordingsAdjusting the Lens Flange Focal Length AdjustmentIris Adjustments Using the zebra pattern in manual adjustment modeSettings for Special Cases 48Adjusting the Lens MacrophotographyEnding close-up shooting Reducing the size of the imageSettings for Special Cases Adjusting Color in the Specified AreaCharacteristics of CCD Sensors Important Notes on OperationDXC-D30/D30P Camera Head VCL-916BYA Zoom LensDesign and specifications are subject to change DXF-701/701CE ViewfinderHood VCL-915BYA/916BY/1012BY Zoom Lens52Chart of Optional Components and Accessories VHS VTRRemoval of Cabinet Board LayoutRemoval of Side Plate Replacement of Main Parts Replacement of CCD UnitDisassembly AssemblyCN2 Connector Input/Output Signals Connectors and CablesPin Signal Specification CAMERA/CA 76P, Male Remote 10P, Female VF 20P, Female HOW to Handle of AT-125 Board Connection ConnectorHow to Attach of the Extension Board EX-591 Replacement Way of ROMIC102DC-DC Converter Voltage External View Check Point Voltage ValueService Mode Operation Service modeMenu screen ConnectionReset object item and standard set value for setting Table Standard set value1 Reset 3 Flare Adjustment4 Pre Knee Setting 2 Standing Correction5 Component Level Adjustment 6 CLP Level Adjustment7 Chroma/VF Adjustment 8 SC adjustment9 Various kinds items setting 10 Test Mode11 Head Block No. information 12 RG, SUB communication13 Various items setting 14 Title Color setting15 Various items setting 16 Knee setting 3 not in used17 Various setting 18 Selfdiagnosis19 Selfdiagnosis 20 Selfdiagnosis21 Selfdiagnosis RC-PMPDRC-CY RC-CCRDSP COM Memory22 Present unit condition indication 23 TG ROM OperationGrayscale chart PreparationEquipment Required Connection Pattern box PTB-500Switch Setting Before Adjustment Adjustment Item Color Bar Signal Confirmation Before AdjustmentSensitivity Measurement Confirmation Camera Adjustment Sub-Carrier Frequency AdjustmentINT SC-H Phase Adjustment 3. Y/R-Y/B-Y CLP Level Adjustment4. Y/SYNC/R-Y/B-Y Level Adjustment Carrier Balance AdjustmentAdjusting point LVL UP LVLChroma VBS Level Adjustment VBS Level Adjustment→ SET UP on MAT Dest Smpte To be extended ES-22 board PreparationChroma YC Level Adjustment YC Level AdjustmentSpecification for Ntsc VF SYNC/BLKG Level Adjustment Specification a = 165 ±5 mVVF Sync → VF Blkg → CAM/DCC+Pedestal Adjustment Shading AdjustmentTest point Spec Mode VA-185 board → R Shad G Shad B ShadFlare Adjustment MIC LEVEL/MIC Level IND AdjustmentAdjusting point Lens iris →CAM/DCC+Character Position Adjustment Title AdjustmentAdjusting point 1CV3/MB-785 board Specification Adjusting point 1CV1/MB-785 board SpecificationPage Sony Corporation

DXC-D30WS, DXC-D30WSP specifications

The Sony DXC-D30WSP and DXC-D30WS are professional broadcast cameras known for delivering exceptional image quality, reliability, and versatility. Both models are part of Sony's renowned lineup of 3-chip CCD cameras, designed to meet the high demands of television production and video broadcasting.

At the heart of the DXC-D30WSP and DXC-D30WS is a high-resolution 3CCD image sensor system. This technology allows for accurate color reproduction and enhanced sensitivity, making it suitable for various lighting conditions. The cameras produce vibrant images with low noise levels, ensuring that footage remains clear and detailed, even in challenging environments.

One of the standout features of these cameras is their adaptability. The DXC-D30WSP model is equipped with a wide range of interchangeable lenses, allowing operators to select the appropriate lens for their specific shooting needs. This flexibility is crucial for cinematographers and videographers who work on diverse projects, from documentaries to commercials.

The DXC-D30WS, which is similar in many ways to its counterpart, emphasizes ease of use with its ergonomic design and intuitive controls. This model is particularly well-suited for field work, as it is lightweight and portable, enabling easy transport without sacrificing performance. Both cameras have comprehensive connectivity options, including SDI and analog outputs, making them compatible with various production environments.

In terms of performance, the Sony DXC-D30WSP and DXC-D30WS feature enhanced digital signal processing. This technology optimizes image quality by improving sharpness, contrast, and color fidelity. In addition to standard recording formats, these cameras support multiple aspect ratios, making them versatile tools for filmmakers who want to achieve specific artistic visions.

Furthermore, both models include advanced white balance and exposure control features, allowing operators to fine-tune settings for optimal results. This precision is critical for maintaining consistent visual quality throughout a production.

In conclusion, the Sony DXC-D30WSP and DXC-D30WS are distinguished by their robust build quality, advanced imaging technologies, and user-friendly designs. They are ideal choices for professionals seeking reliable, high-performance cameras that can adapt to a wide range of shooting situations. Whether for broadcast television or independent filmmaking, these cameras remain a valuable asset in any production setup, ensuring that creators can capture stunning visuals with ease.
Top Page Image Contents