Sony DXC-D30WS Using Accessories, Fitting to a Tripod, Adjusting the Shoulder Pad Position

Page 26

1-22

Using Accessories

Fitting an optional microphone

Use the following procedure to attach an optional ECM-670 Microphone.

1 Loosen the screw of the CAC-

12 Microphone Holder, then

open the holder and replace the

microphone adaptor with the

Microphone adaptor

Fitting to a Tripod

First fit the VCT-U14 Tripod Adaptor to the tripod,

Pin

then mount the camera on the tripod adaptor.

 

 

one supplied with the ECM-

 

 

Chapter 2

670 Microphone.

 

Fitting and

2 Insert the microphone in the

Connections

microphone holder, close the

holder, and tighten the screw.

Connect the microphone cable

 

to the MIC IN +48 V

 

connector.

MIC IN +48 V connector

Mark

VCT-U14 Tripod Adaptor

Side the camera forward along the slot, until it clicks firmly into place.

Tripod

Adjusting the Shoulder Pad Position

You can slide the shoulder pad toward the front or back by up to 10 mm from its central position (as when shipped). Adjust it to get the best balance when using the camera on your shoulder.

Chapter 2 Fitting and Connections

Fitting optional microphones (operable with a 48 V supply) other than the ECM-670

Use the same fitting procedure as for the ECM-670, but note the following differences with respect to the microphone adaptor.

ECM-672:no microphone adaptor required.

Slender microphones (19 mm (3/4 inch) diameter):

use the microphone adaptor supplied with the CAC-12.

Removal

Hold down the red button and pull the lever in the direction of the arrow.

Note

After removing the camera, if the tripod adaptor pin has not returned to its original position, hold down the red button and move the lever in the direction of the arrow to return the pin to its original position. It is not possible to mount a camera with the pin left out.

 

1

2

Loosen the

two screws.

 

Adjust the position, then tighten the screws.

Optional CAC-4 Chest Pad

When using the camera on your shoulder, attaching the optional CAC-4 Chest Pad reduces the load on your right hand supporting the zoom lens, and makes operation easier.

For details see the instructions provided with the CAC-4.

DXC-

 

 

D30WS/P(E)/V1

30

Chapter 2 Fitting and Connections

 

Chapter 2 Fitting and Connections

31

Page 25 Page 27
Image 26
Page 25 Page 27
Contents
DXC-D30WS DXC-D30WSP Varning Manual Structure Introducing this manual Related manualsTable of Contents Digital Video Camera Operating instructionsTable of Contents About This Manual Overview Advanced Menu SettingsFeatures ItemSettings Battery Pack Operating TimesAdvanced Menu Settings Video Output and Viewfinder Picture Related Products SpecificationsSupplied accessories DXC-D30WSL/D30WSPL Camera HeadHorizontal resolution in 169 mode SpecificationsMeasuring Horizontal Resolution Horizontal resolution in 43 modeChart of Optional Components and Accessories DXCCamera Head VCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Using the Camcorder GripUsing Battery Packs Camera Adaptor Power Supply Table of Contents Product Configurations Camera adaptorFeatures Location and Function of Parts Camera HeadLocation and Function of Parts Front view Left and upper viewVCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Location and Function of Parts Attaching a camcorder grip to the DSR-1/1P Using the Camcorder Grip Fitting a VTR To remove the VTRFitting a VTR Attaching a camcorder grip to the PVV-3/3PFitting optional filters If using a lens with a 6-pin connectorFitting the Lens Using an Optional Microphone Using AccessoriesUsing the Viewfinder Fitting to a Tripod Using AccessoriesAdjusting the Shoulder Pad Position Fitting an optional microphoneConnections Using Accessories Using the Carrying CaseConnecting a Portable VTR Connected VTR Connecting a Number of Cameras Using a Camera Control UnitConnections VTRBattery pack operating times Power SupplyUsing Battery Packs Battery low indicationsCamera with a separate power supply Basic Procedure for ShootingPower Supply Camera Adaptor Power Supply Filter setting Lighting conditionsShooting with the DSR-1/1P Basic Procedure for ShootingUsing the ClipLink Function Reviewing the recordingSetting cue points as you shoot Using the Edit Search Function While Back Space EditingSetting Mark IN/OUT points as you shoot Shooting with the DSR-1/1PChanging the Viewfinder Display Using the Freeze Mix FunctionViewfinder Screen Indications Viewfinder Normal Indications Viewfinder Screen IndicationsViewfinder Normal Indications Status Indications Contents and Settings of EachViewfinder Basic Menu Basic Menu OperationsViewfinder Basic Menu Setting the recording time in secondsSetting the recording time in minutes DSR-1/1P Basic menu pages 8Entering the title To record a titleTo change Viewfinder Advanced MenuAdvanced Menu Operations To return to the normal indicationsViewfinder Advanced Menu Advanced menu pages 13 EZ mode settingsAdvanced menu pages 9 to To set the camera IDUsing the DSR-1/1P 38Setup FilesCalling up a Setup File To call up files recorded onto a tape whenTo save setup files to a tape when using the DSR-1/1P Setup Files Changing File SettingsSaving File Settings Setting up the camera Using Data Recorded on Tape Using SetupNavi and SetupLog with the DSR-1/1PSetup Files Viewing SetupLog Data Using SetupNavi and SetupLog with the DSR-1/1PRecording the Menu Settings onto a Tape To abort the data recording while in progressWhite Balance Adjustment Saving an Appropriate White Balance Value in MemoryUsing the ATW Auto Tracing White Balance Function White Balance AdjustmentLight Sources and Color Temperature Using the Preset White Balance SettingsShutter speeds 44Black Balance Adjustment Shutter SettingsSetting the shutter speed, CLS and EVS function CLS Clear Scan functionHow to set the date and time Setting the Clock and Timestamping RecordingsShutter Settings When shooting is finishedViewfinder Screen Adjustments 46Setting the Clock and Timestamping RecordingsIris Adjustments Adjusting the LensFlange Focal Length Adjustment Using the zebra pattern in manual adjustment modeEnding close-up shooting Settings for Special Cases48Adjusting the Lens Macrophotography Reducing the size of the imageCharacteristics of CCD Sensors Settings for Special CasesAdjusting Color in the Specified Area Important Notes on OperationDXC-D30/D30P Camera Head VCL-916BYA Zoom LensHood Design and specifications are subject to changeDXF-701/701CE Viewfinder VCL-915BYA/916BY/1012BY Zoom Lens52Chart of Optional Components and Accessories VHS VTRRemoval of Side Plate Board LayoutRemoval of Cabinet Disassembly Replacement of Main PartsReplacement of CCD Unit AssemblyCN2 Pin Signal Specification Connectors and CablesConnector Input/Output Signals CAMERA/CA 76P, Male Remote 10P, Female VF 20P, Female How to Attach of the Extension Board EX-591 HOW to Handle of AT-125 BoardConnection Connector Replacement Way of ROMIC102DC-DC Converter Voltage External View Check Point Voltage ValueMenu screen Service Mode OperationService mode ConnectionReset object item and standard set value for setting Table Standard set value4 Pre Knee Setting 1 Reset3 Flare Adjustment 2 Standing Correction7 Chroma/VF Adjustment 5 Component Level Adjustment6 CLP Level Adjustment 8 SC adjustment11 Head Block No. information 9 Various kinds items setting10 Test Mode 12 RG, SUB communication15 Various items setting 13 Various items setting14 Title Color setting 16 Knee setting 3 not in used17 Various setting 18 Selfdiagnosis19 Selfdiagnosis 20 SelfdiagnosisRC-CY 21 SelfdiagnosisRC-PMPD RC-CCRDSP COM Memory22 Present unit condition indication 23 TG ROM OperationEquipment Required Connection Grayscale chartPreparation Pattern box PTB-500Switch Setting Before Adjustment Adjustment Item Sensitivity Measurement Confirmation Before AdjustmentColor Bar Signal Confirmation INT SC-H Phase Adjustment Camera AdjustmentSub-Carrier Frequency Adjustment 3. Y/R-Y/B-Y CLP Level AdjustmentAdjusting point 4. Y/SYNC/R-Y/B-Y Level AdjustmentCarrier Balance Adjustment LVL UP LVL→ SET UP on MAT Dest Smpte Chroma VBS Level AdjustmentVBS Level Adjustment To be extended ES-22 board PreparationSpecification for Ntsc YC Level AdjustmentChroma YC Level Adjustment VF Sync → VF Blkg VF SYNC/BLKG Level AdjustmentSpecification a = 165 ±5 mV → CAM/DCC+Test point Spec Mode VA-185 board Pedestal AdjustmentShading Adjustment → R Shad G Shad B ShadAdjusting point Lens iris Flare AdjustmentMIC LEVEL/MIC Level IND Adjustment →CAM/DCC+Adjusting point 1CV3/MB-785 board Specification Character Position AdjustmentTitle Adjustment Adjusting point 1CV1/MB-785 board SpecificationPage Sony Corporation
Top Page Image Contents