Sony DXC-D30WSP service manual Chroma VBS Level Adjustment, To be extended ES-22 board Preparation

Page 83

3-3-6. Chroma (VBS) Level Adjustment

Equipment: Verctorscope

To be extended: ES-22 board

Preparation:

GAIN switch/Verctorscope 75 % CAL

Adjust the PHASE control on the vectorscope so that the burst spot is overlapped to the 75 % axis.

OUTPUT/DL/DCC+switch/camera side BARS

Test point: VIDEO OUT connector/camera side

Adjustment Procedure:

1.[for NTSC]

SERVICE menu “PAGE 7”

B-Y BST :

Note: In case of NTSC, make sure that “R-Y BST” must be “0”.

Adjust the UP 4switch or DOWN $ switch so that burst spot is located at 75 % scale mark on the vectorscope screen.

[for PAL]

• SERVICE menu “PAGE 7”

R-Y BST :

B-Y BST :

Adjust “R-Y BST” and “B-Y BST” alternately by UP 4 switch or DOWN $ switch so that burst spot is located at 75 % scale mark on the vectorscope screen.

2.Adjust the following controls alternately so that each beam spot stays inside the reference frame “ 4”.

1RV503 (B-Y LEV)/ES-22 board

1FL502 (PHASE)/ES-22 board

1RV504 (CHROMA VBS LEV)/ ES-22 board

3.Then, perform above procedure item 1 again.

[for NTSC]

 

[for PAL]

 

 

MG

 

R

 

 

R

 

MG

 

 

 

 

 

 

 

75%

 

YL

 

YL

100%

 

 

 

 

 

B

 

 

B

G

CY

G

CY

 

 

 

 

3-3-7. Y (VBS) Level Adjustment

Equipment: Waveform monitor

To be extended: ES-22 board

Preparation: OUTPUT/DL/DCC+switch/camera side BARS

Test point: VIDEO OUT connector/camera side

Adjustment Procedure

1.[for NTSC]

• SERVICE menu “PAGE 9”

SET UP : ON MAT DEST : SMPTE

• SERVICE menu “PAGE 5”

S-UP LVL :

Adjust the UP 4 switch or DOWN $ switch. Specification : A = 7.5 ±0.5 IRE (See below

waveform) ---- NTSC only

[for PAL]

SERVICE menu “PAGE 9”

COMP LVL : 525 (not 700)

2.Adjusting point: 1RV501 (Y LEVEL)/ES-22 board

Specification:

[for NTSC]

B = 100

±2 IRE

 

[for PAL]

B = 700

±10 mV

[for NTSC]

 

[for PAL]

FL501

 

 

 

 

 

 

 

 

 

DL503

CN501

 

 

 

 

 

 

 

FL502

 

 

 

DL501

 

 

 

 

 

 

 

 

 

DL504

 

 

 

FL503

 

 

DL502

 

RV503

RV505

RV501

E1

B-Y LEV

C (Y-C)

Y (VBS)

TP1

 

 

 

 

 

 

RV504

RV502

 

 

C (VBS)

Y (Y-C)

ES-22 BOARD -A SIDE-

 

 

 

 

DXC-D30WS/P(E)/V1

3-7

 

Image 83
Contents DXC-D30WS DXC-D30WSP Varning Introducing this manual Related manuals Manual StructureTable of Contents Operating instructions Digital Video CameraTable of Contents About This Manual Overview Advanced Menu SettingsFeatures ItemSettings Battery Pack Operating TimesAdvanced Menu Settings Video Output and Viewfinder Picture DXC-D30WSL/D30WSPL Camera Head SpecificationsSupplied accessories Related ProductsHorizontal resolution in 43 mode SpecificationsMeasuring Horizontal Resolution Horizontal resolution in 169 modeDXC Chart of Optional Components and AccessoriesCamera Head VCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Using the Camcorder GripUsing Battery Packs Camera Adaptor Power Supply Table of Contents Camera adaptor Product ConfigurationsFeatures Camera Head Location and Function of PartsLocation and Function of Parts Left and upper view Front viewVCL-916BYA Zoom Lens DXF-701/701CE Viewfinder Location and Function of Parts To remove the VTR Using the Camcorder GripFitting a VTR Attaching a camcorder grip to the DSR-1/1PAttaching a camcorder grip to the PVV-3/3P Fitting a VTRFitting optional filters If using a lens with a 6-pin connectorFitting the Lens Using an Optional Microphone Using AccessoriesUsing the Viewfinder Fitting an optional microphone Using AccessoriesAdjusting the Shoulder Pad Position Fitting to a TripodConnections Using Accessories Using the Carrying CaseConnecting a Portable VTR VTR Connecting a Number of Cameras Using a Camera Control UnitConnections Connected VTRBattery low indications Power SupplyUsing Battery Packs Battery pack operating timesFilter setting Lighting conditions Basic Procedure for ShootingPower Supply Camera Adaptor Power Supply Camera with a separate power supplyReviewing the recording Basic Procedure for ShootingUsing the ClipLink Function Shooting with the DSR-1/1PShooting with the DSR-1/1P Using the Edit Search Function While Back Space EditingSetting Mark IN/OUT points as you shoot Setting cue points as you shootChanging the Viewfinder Display Using the Freeze Mix FunctionViewfinder Screen Indications Viewfinder Screen Indications Viewfinder Normal IndicationsViewfinder Normal Indications Basic Menu Operations Contents and Settings of EachViewfinder Basic Menu Status IndicationsViewfinder Basic Menu Setting the recording time in secondsSetting the recording time in minutes To record a title Basic menu pages 8Entering the title DSR-1/1PTo return to the normal indications Viewfinder Advanced MenuAdvanced Menu Operations To changeViewfinder Advanced Menu To set the camera ID EZ mode settingsAdvanced menu pages 9 to Advanced menu pages 13To call up files recorded onto a tape when 38Setup FilesCalling up a Setup File Using the DSR-1/1PTo save setup files to a tape when using the DSR-1/1P Setup Files Changing File SettingsSaving File Settings Setting up the camera Using Data Recorded on Tape Using SetupNavi and SetupLog with the DSR-1/1PSetup Files To abort the data recording while in progress Using SetupNavi and SetupLog with the DSR-1/1PRecording the Menu Settings onto a Tape Viewing SetupLog DataSaving an Appropriate White Balance Value in Memory White Balance AdjustmentUsing the Preset White Balance Settings White Balance AdjustmentLight Sources and Color Temperature Using the ATW Auto Tracing White Balance FunctionCLS Clear Scan function 44Black Balance Adjustment Shutter SettingsSetting the shutter speed, CLS and EVS function Shutter speedsWhen shooting is finished Setting the Clock and Timestamping RecordingsShutter Settings How to set the date and time46Setting the Clock and Timestamping Recordings Viewfinder Screen AdjustmentsUsing the zebra pattern in manual adjustment mode Adjusting the LensFlange Focal Length Adjustment Iris AdjustmentsReducing the size of the image Settings for Special Cases48Adjusting the Lens Macrophotography Ending close-up shootingImportant Notes on Operation Settings for Special CasesAdjusting Color in the Specified Area Characteristics of CCD SensorsVCL-916BYA Zoom Lens DXC-D30/D30P Camera HeadVCL-915BYA/916BY/1012BY Zoom Lens Design and specifications are subject to changeDXF-701/701CE Viewfinder HoodVHS VTR 52Chart of Optional Components and AccessoriesRemoval of Side Plate Board LayoutRemoval of Cabinet Assembly Replacement of Main PartsReplacement of CCD Unit DisassemblyCN2 Pin Signal Specification Connectors and CablesConnector Input/Output Signals CAMERA/CA 76P, Male Remote 10P, Female VF 20P, Female Replacement Way of ROMIC102 HOW to Handle of AT-125 BoardConnection Connector How to Attach of the Extension Board EX-591External View Check Point Voltage Value DC-DC Converter VoltageConnection Service Mode OperationService mode Menu screenStandard set value Reset object item and standard set value for setting Table2 Standing Correction 1 Reset3 Flare Adjustment 4 Pre Knee Setting8 SC adjustment 5 Component Level Adjustment6 CLP Level Adjustment 7 Chroma/VF Adjustment12 RG, SUB communication 9 Various kinds items setting10 Test Mode 11 Head Block No. information16 Knee setting 3 not in used 13 Various items setting14 Title Color setting 15 Various items setting18 Selfdiagnosis 17 Various setting20 Selfdiagnosis 19 SelfdiagnosisRC-CCR 21 SelfdiagnosisRC-PMPD RC-CYMemory DSP COM23 TG ROM Operation 22 Present unit condition indicationPattern box PTB-500 Grayscale chartPreparation Equipment Required ConnectionSwitch Setting Before Adjustment Adjustment Item Sensitivity Measurement Confirmation Before AdjustmentColor Bar Signal Confirmation 3. Y/R-Y/B-Y CLP Level Adjustment Camera AdjustmentSub-Carrier Frequency Adjustment INT SC-H Phase AdjustmentLVL UP LVL 4. Y/SYNC/R-Y/B-Y Level AdjustmentCarrier Balance Adjustment Adjusting pointTo be extended ES-22 board Preparation Chroma VBS Level AdjustmentVBS Level Adjustment → SET UP on MAT Dest SmpteSpecification for Ntsc YC Level AdjustmentChroma YC Level Adjustment → CAM/DCC+ VF SYNC/BLKG Level AdjustmentSpecification a = 165 ±5 mV VF Sync → VF Blkg→ R Shad G Shad B Shad Pedestal AdjustmentShading Adjustment Test point Spec Mode VA-185 board→CAM/DCC+ Flare AdjustmentMIC LEVEL/MIC Level IND Adjustment Adjusting point Lens irisAdjusting point 1CV1/MB-785 board Specification Character Position AdjustmentTitle Adjustment Adjusting point 1CV3/MB-785 board SpecificationPage Sony Corporation

DXC-D30WS, DXC-D30WSP specifications

The Sony DXC-D30WSP and DXC-D30WS are professional broadcast cameras known for delivering exceptional image quality, reliability, and versatility. Both models are part of Sony's renowned lineup of 3-chip CCD cameras, designed to meet the high demands of television production and video broadcasting.

At the heart of the DXC-D30WSP and DXC-D30WS is a high-resolution 3CCD image sensor system. This technology allows for accurate color reproduction and enhanced sensitivity, making it suitable for various lighting conditions. The cameras produce vibrant images with low noise levels, ensuring that footage remains clear and detailed, even in challenging environments.

One of the standout features of these cameras is their adaptability. The DXC-D30WSP model is equipped with a wide range of interchangeable lenses, allowing operators to select the appropriate lens for their specific shooting needs. This flexibility is crucial for cinematographers and videographers who work on diverse projects, from documentaries to commercials.

The DXC-D30WS, which is similar in many ways to its counterpart, emphasizes ease of use with its ergonomic design and intuitive controls. This model is particularly well-suited for field work, as it is lightweight and portable, enabling easy transport without sacrificing performance. Both cameras have comprehensive connectivity options, including SDI and analog outputs, making them compatible with various production environments.

In terms of performance, the Sony DXC-D30WSP and DXC-D30WS feature enhanced digital signal processing. This technology optimizes image quality by improving sharpness, contrast, and color fidelity. In addition to standard recording formats, these cameras support multiple aspect ratios, making them versatile tools for filmmakers who want to achieve specific artistic visions.

Furthermore, both models include advanced white balance and exposure control features, allowing operators to fine-tune settings for optimal results. This precision is critical for maintaining consistent visual quality throughout a production.

In conclusion, the Sony DXC-D30WSP and DXC-D30WS are distinguished by their robust build quality, advanced imaging technologies, and user-friendly designs. They are ideal choices for professionals seeking reliable, high-performance cameras that can adapt to a wide range of shooting situations. Whether for broadcast television or independent filmmaking, these cameras remain a valuable asset in any production setup, ensuring that creators can capture stunning visuals with ease.