Hasselblad 10026 service manual Reassembly

Page 13

4:1

Camera body 503CW

Reassembly

The lubricants mentioned in the text are:

Grease = Isoflex Topas L32

Oil = Isoflex PDP 48

Gear housing (30324)

Lubricate carefully the washer (810840) with oil. Lubricate with grease and fit (incl. the above mentioned washer) the ratchet wheel (20924) into the front section of the gear housing (30304).

Lubricate with grease and fit the gear wheel (13169).

Note. The correct relationship between the two gears before inserting the locking pin (812106) into the shaft.

Fit the locking ring (810938) and the activating hook (20919), lubricate carefully with oil. Fit the spring (816504) and the washer (810826).

Place the stop gear (13509) into the rear section of the gear housing (13157).

Lubricate the shaft of the ratchet wheel (20924) and put the front and rear section together.

821033
13157
22355
13509
810826
816504
812106
810938
13169
20919
810840
30304
20924

Fig. 11

Fit the mirror cam (22355) and secure with the screw (821033).

Note! The position of the mirror cam (22355) relative to ratchet wheel (20924).

Fig.11.

Mechanism plate (21125-1)

Ensure the auxiliary shutter release connecting rod coupling and the control gear wheel move freely (i.e. with no friction). Lubricate lightly with oil. Lubricate the gear wheel’s cam with grease.

If it is necessary to replace the coil spring (30384) fit it
into the spring mounting on gear wheel (22699) as
shown in fig.12. Use a new spring, contained in its
plastic ring. Lubricate with grease.	Fig. 12
Revision 1	May 2000

Image 13

Contents Göteborg Sweden Victor Hasselblad ABContents list Camera body 503CW Signal arm shortened 501C and 503CXi Updated pages 503CXiFitted with wrong spacers 503C/M and 503CX Flash metering circuit redesigned 503CX04/01 New CD-ROM Version Camera type General descriptionRelease sequence Tools Used for Tool No DescriptionTool No Description Used for Camera shell Front bayonet plate Circuit board 22575 *22882Rear plate 30300 including auxiliary shutter Right hand wall Focusing screen frameMechanism plate Gear housing Reassembly 816802 Fitting the mechanism plate to the right hand wall 821631 13108 814827 13355 13280 13362 Rear plate Front plate Perform the necessary adjustment as described in sectionIntermediate gear Adjustment Focal length Adjustment of the front key’s angular positionAngle 15-16 o with the bayonet plate tool 904644 pushed Adjustment of the release mechanism 15 mm Adjustment of the release sequence Fitting the damping ring Fitting the Circuit board 22575 *22882 Adjustment Fitting the camera body into the shellFinal checks 510 Camera body 503CW 511 Camera body 503CW 512 Camera body 503CW 513 Camera body 503CW Front gear Front plate reassemblyFront bayonet plate Exchanging the auxiliary shutter Exchanging the mirrorShim washers Revision May Pos Pcs Spare Description Remark May Camera body 503CW Camera body 503CW Camera body 503CW September Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW October May Camera body 503CW Camera body 503CW 151 Spare parts not listed are the same as for 503CW 152 152 153 153 154 154 155 Coupling Crank support 161 Pos Pcs No Spare Part No Description Remark 162 Pos Pcs Spare Description Remark 163 163 171 171 172 172 173 173 174 174 175 175 181 181 182 182 183 183 184 184 185 January 191 October 192 192 193 193