Hasselblad 10026 service manual 816802

Page 14

4:2

Camera body 503CW

Reassembly

Mount the gear housing (30324) to the mechanism plate.

On the reverse side of the mechanism plate lubricate the hub with grease and fit the shutter stop bar (20912) spring (816802), washer (810404) and clip (817112). Fig. 13.

Note! The gear housing must be rotated when fitting the stop bar (20912).

Lubricate the cam of the gear wheel (13182) with grease and fit to the mechanism plate.

Note! The position of the gear wheel engagement according to fig.14.

Hold the gear wheels in position and on the reverse side of the mechanism plate, position washer (810932) and lubricate the hub with grease. Fit gear wheel (22699) together with the coil spring. Lubricate the coil spring with grease.

Assemble the lid (14280) and temporarily secure with the screw (822605). Fig. 15.

Tension the spring by rotating the gear wheel (22699) in the direction shown in fig. 14. Test the operation by pushing the shutter release connecting rod up and down several times (tension the spring after each operation). The gear wheels should rotate freely. Fig. 14.

20912	816802
	810404
	817112

30324

Fig. 13

13182 22699

Gear alignment

Fig. 14

14280

822605

Gear housing

Fig. 15

Lubricate with grease and fit the intermediate gear wheel (13167), bearing bracket (13171), nut (13116) and two screws (820016).

Position the bearing bracket (13171) and mesh the gear teeth, secure the two mounting screws (820016).

Fig. 16.

	820016
	13116
	13171
Mounting	13167
position	13167

Fig. 16

Revision 2

May 2000

Image 14

Contents Victor Hasselblad AB Göteborg SwedenContents list Camera body 503CW Fitted with wrong spacers 503C/M and 503CX Updated pages 503CXiSignal arm shortened 501C and 503CXi Flash metering circuit redesigned 503CX04/01 New CD-ROM Version General description Camera typeRelease sequence Tool No Description Tools Used forTool No Description Used for Camera shell Rear plate 30300 including auxiliary shutter Circuit board 22575 *22882Front bayonet plate Mechanism plate Focusing screen frameRight hand wall Gear housing Reassembly 816802 Fitting the mechanism plate to the right hand wall 821631 13108 814827 13355 13280 13362 Rear plate Intermediate gear Perform the necessary adjustment as described in sectionFront plate Adjustment Adjustment of the front key’s angular position Focal lengthAngle 15-16 o with the bayonet plate tool 904644 pushed Adjustment of the release mechanism 15 mm Adjustment of the release sequence Fitting the damping ring Adjustment Fitting the camera body into the shell Fitting the Circuit board 22575 *22882Final checks 510 Camera body 503CW 511 Camera body 503CW 512 Camera body 503CW 513 Camera body 503CW Front plate reassembly Front gearFront bayonet plate Exchanging the mirror Exchanging the auxiliary shutterShim washers Revision May Pos Pcs Spare Description Remark May Camera body 503CW Camera body 503CW Camera body 503CW September Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW October May Camera body 503CW Camera body 503CW 151 Spare parts not listed are the same as for 503CW 152 152 153 153 154 154 155 Coupling Crank support 161 Pos Pcs No Spare Part No Description Remark 162 Pos Pcs Spare Description Remark 163 163 171 171 172 172 173 173 174 174 175 175 181 181 182 182 183 183 184 184 185 January 191 October 192 192 193 193