Hasselblad 10026 service manual 821631 13108 814827 13355 13280 13362

Page 16

4:4

Camera body 503CW

Reassembly

Fit the stop lever (13355) and spring (816752) to the pre-greased hub. Secure with the clip (817119).

Lubricate the hub (13108) with grease and place a shim onto it. This shim can be in several thicknesses for adjustment as follows: 0.10; 0.20; 0.30 mm with corresponding part numbers 810826, 810827, 810828. Attach spring (814827) between the auxiliary shutter stop (22436) and the right hand wall.

Fig. 19.

On the reverse side of the right hand wall fit the mirror actuating lever (13362) and the lens lock (13280). Lubricate with grease. The lens lock pin (13280) fits into a pin on the mirror actuating lever.

Fig. 20.

Secure the mirror actuating lever (13362) temporarily with screw (821631) from the other side according to Fig. 19.

821631

13108

814827

13355

Fig. 19

13280

13362

Fit the mirror catch 13356-1 onto the pin. Lubricate with grease. Connect the spring (816720) with its long shackle in the hole in the right hand wall and the short one under the mirror catch.

Hold the blocking lever and spring and install the push fit cover (30727). Check that the mirror catch moves freely.

Fig. 21.

Connect the right and left hand walls to the bottom plate (30686), secure with six screws (820014). Apply safety lacquer to screw-threads.

Put back the foam plastic pad (22582).

Focusing screen frame (22812)

Put the focusing screen frame back and at the same time secure the upper part of the inner side cover (22813). Fit the spring (30755) and secure with screws (829425). Fit four screws (820015), two through the right hand wall and two (temporarily) through the left hand wall. Fig. 22.

Fig. 20

13356-1

816720

30727

Fig. 21

Cover 22813

Fig. 22

Revision 1

January 2001

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Victor Hasselblad AB Göteborg SwedenContents list Camera body 503CW Updated pages 503CXi Signal arm shortened 501C and 503CXiFitted with wrong spacers 503C/M and 503CX Flash metering circuit redesigned 503CX04/01 New CD-ROM Version General description Camera typeRelease sequence Tool No Description Tools Used forTool No Description Used for Camera shell Front bayonet plate Circuit board 22575 *22882Rear plate 30300 including auxiliary shutter Right hand wall Focusing screen frameMechanism plate Gear housing Reassembly 816802 Fitting the mechanism plate to the right hand wall 821631 13108 814827 13355 13280 13362 Rear plate Front plate Perform the necessary adjustment as described in sectionIntermediate gear Adjustment Adjustment of the front key’s angular position Focal lengthAngle 15-16 o with the bayonet plate tool 904644 pushed Adjustment of the release mechanism 15 mm Adjustment of the release sequence Fitting the damping ring Adjustment Fitting the camera body into the shell Fitting the Circuit board 22575 *22882Final checks 510 Camera body 503CW 511 Camera body 503CW 512 Camera body 503CW 513 Camera body 503CW Front plate reassembly Front gearFront bayonet plate Exchanging the mirror Exchanging the auxiliary shutterShim washers Revision May Pos Pcs Spare Description Remark May Camera body 503CW Camera body 503CW Camera body 503CW September Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW Camera body 503CW October May Camera body 503CW Camera body 503CW 151 Spare parts not listed are the same as for 503CW 152 152 153 153 154 154 155 Coupling Crank support 161 Pos Pcs No Spare Part No Description Remark 162 Pos Pcs Spare Description Remark 163 163 171 171 172 172 173 173 174 174 175 175 181 181 182 182 183 183 184 184 185 January 191 October 192 192 193 193
Top Page Image Contents