JVC TK-C1430 Connecting the control signal cable, Setting the switches , When connecting

Page 13

Connecting the control signal cable

(Use a twisted-pair cable for connection. Page 17.)

Camera 1 control signal connection terminals

TX+ A

TX B

RX+ C

RX D

Camera 2 control signal connection terminals

TX+ A

TX B

RX+ C

RX D

RM-P2580

A RX +

BRX

CTX +

DTX

Connect:

Camera TX+ to RM-P2580 RX+ Camera TX– to RM-P2580 RX– Camera RX+ to RM-P2580 TX+ Camera RX– to RM-P2580 TX–

The A B C D marks indicated on both the camera terminals and the RM-P2580 termi- nals facilitate correct connections. Connect the terminals with identical marks.

Setting the switches ( Page 10)

SET
	CAMERA
AWC	SETUP	EXT TERM-OFF	ON
MENU		INT/GL	LL
		DUPLEX	SIMPLEX
		RX TERM-OFF	ON
		NOT USED
			IRIS
			VIDEO
			DC

EXT TERM-OFF

INT/GL

DUPLEX

RX TERM-OFF

NOT USED

ON

LL

SIMPLEX

ON

Select the synchronization method of the camera image.

Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE.

( Page 26.)

Set this switch to the DUPLEX

*If the setting is changed, be absolutely sure to switch on the power again.

Set this switch to ON (signal termination ON) only on the camera placed at the end of the control signal cable.

Set to OFF on all other cameras.

Setting on the MENU screen ( Page 35)

* If the setting is changed, escape from the menu screen once, and definitely switch on the power again.

C OMMUN I C A T I O N
S T YL E	M . DROP
MACH I NE I D	1

Set to M.DROP

Set to M.DROP when the RM-P2580 is used as a remote control unit. When controlling from another machine, make sure that it matches the communication system used.

MACHINE ID setting switches

Set this item to match the RM-P2580 VIDEO INPUT terminal number for each camera.

When connecting

●Turn OFF the power supply to all equipment to be used before making connections.

●Carefully read the Instructions for each piece of equipment to be used before making connections.

●For the appropriate connection cables and the length of these, carefully read “Connections on the back” on page 16.

●The control signal cable cannot be used for loop connection.

E-13

Image 13

Contents TK-C1430 Important Safeguards Page Safety Precautions Contents Memo FeaturesReference page or item Operating Precautions Lens mount Controls, Connectors and IndicatorsCamera-mounting screw Hole 1/4 inch Rotation-preventive holeCover 12 SET/AWC Set. Auto White Control VIDEO/DC Iris Selector SwitchButton Iris Iris TerminalDUPLEX, Simplex Selector Switch for Transmission System 15 INT/GL, LL Selector Switch for Synchronizing System17 RX.TERM-ON/OFF RX SignalTerminal ON/OFF Switch 13 , , , Up-and-down, left-and- right ButtonVideo OUT Video signal output connector 22 Y/C OUT Y/C output connectorPower Power indicator lamp This lamp lights when power is supplied to the camera System with up to 8 cameras RM-P2580 System Setting the switches Connecting the control signal cable Setting on the Menu screen When connectingSetting the switches ProceduresMounting the lens Mount the lens according to the procedures described belowDC Iris Video Iris VideoConnections on the back Installing the ferrite core Genlock connection Control signal cablesFall Prevention Mounting the cameraSpecified screw M3 ⋅ 6 mm Installation of camera Level adjustment Lens adjustmentDoes not operate Back focus adjustment Back focus adjustmentLens Focus Adjustment Mode With a fixed-focus lensError message display Auto white balance control adjustmentMenu screen is displayed Setting the menuSelected sub-menu screen is displayed Change of the set value displays a change mark ∗Flow of menu screen Menu SettingC SE T T I NGS I S L E VE L Normal AV Erage P EAK ALC Settings Screen Sync Adjust ScreenFunctions and set values Initial value Memo Memo Motion PriorityBLC OFFMode ColourAUX AutoVideo Adjust Screen Mode Select Screen Zoom Terminal MotionMAX Motion Detect Screen Alarm TimeArea Edit Factory Settings Screen Maintenance ScreenCommunication Screen EDIT1 screen is brought up BLC Editting ScreenSides having marks can be changed Manual Adjustment of White Balance Screen returns to Mode Select Camera Title SettingThen, the Camera Title screen is brought up Selected character is displayed flashing on and offSetting screen is brought up Setting the Motion Detect FunctionSelect the item Area Edit on Motion Detect screenSet the B&W Item to Auto Output of Black-White/Color switching signalSet the B&W item to AUX B&W/COLOR Mode screen appearsOperation method White spot compensationConfirm that the cursor is at the item CCD Spot screen will be dis- playedDimensions Unit mm SpecificationsVideo OUT OUTTK-C1430 Colour Video Camera