JVC TK-C1430 Mounting the lens, Mount the lens according to the procedures described below, Video

Page 15

Mounting the lens

Mount the lens according to the procedures described below.

(b)F

(c)

3.

VIDEO

DC

2.

IRIS

VIDEO

DC

4.

1. Before mounting a lens, check whether it is a C-mount or CS-mount lens.

To change the mounting method, loosen the back-focus locking screw (M 2.6) using a Phillips head screwdriver, turn the back-focus adjusting ring with your fingers or the screwdriver and change the mounting method.

As regards the dimension (b) of the area to which the lens is to be installed as illustrated on the left diagram, use the one with less value than what’s shown in the table below.

For both the C-mount and CS-mount, never use whatever exceeds the dimen- sion (b), as such will not allow normal installation and damage the inner part of the camera, resulting in a malfunc- tion.

Lens	Flange back (c)	Dimension (b)

C mount lens	17.526mm	5.5mm or less

CS mount lens	12.5mm	5.5mm or less

The F mark indicates a focal point.

	1	3





		4
	2	4

	CAUTION:
3	Always attach the fer-
1	rite core (supplied) to
	rite core (supplied) to
4	the lens cable.
2	( Page 16)

Attached 4 pin plugs

2. Mount the lens on the camera by turning the lens clockwise. Adjust its position.

3. When using an auto-iris lens with an EE amplifier, turn the switch to the “VIDEO” side. When no EE amplifier is equipped, turn the switch to the “DC” side.

4. If the lens has an auto-iris mechanism, connect the lens cable after checking the pin arrangement.

If the lens cable has a different type of plug, use the 4-P plug supplied.

Lens	DC IRIS		VIDEO IRIS
Pin No.	(does not contain EE amplifier)		(contain EE amplifier)
1	Brake	–	9V [max 50mA]
2	Brake +		NC
3	Drive	+	VIDEO
4	Drive	–	GND

13

24

E-15

Image 15

Contents TK-C1430 Important Safeguards Page Safety Precautions Contents Features MemoReference page or item Operating Precautions Rotation-preventive hole Controls, Connectors and IndicatorsLens mount Camera-mounting screw Hole 1/4 inchIris Iris Terminal VIDEO/DC Iris Selector SwitchCover 12 SET/AWC Set. Auto White Control Button13 , , , Up-and-down, left-and- right Button 15 INT/GL, LL Selector Switch for Synchronizing SystemDUPLEX, Simplex Selector Switch for Transmission System 17 RX.TERM-ON/OFF RX SignalTerminal ON/OFF SwitchThis lamp lights when power is supplied to the camera 22 Y/C OUT Y/C output connectorVideo OUT Video signal output connector Power Power indicator lamp System with up to 8 cameras RM-P2580 SystemWhen connecting Connecting the control signal cable Setting the switches Setting on the Menu screen Setting the switches ProceduresVideo Mount the lens according to the procedures described belowMounting the lens DC Iris Video IrisConnections on the back Installing the ferrite core Genlock connection Control signal cablesMounting the camera Fall PreventionSpecified screw M3 ⋅ 6 mm Installation of camera Lens adjustment Level adjustmentDoes not operate With a fixed-focus lens Back focus adjustment Back focus adjustment Lens Focus Adjustment ModeError message display Auto white balance control adjustmentChange of the set value displays a change mark ∗ Setting the menuMenu screen is displayed Selected sub-menu screen is displayedFlow of menu screen Menu SettingC SE T T I NGS I S L E VE L Normal AV Erage P EAK Sync Adjust Screen ALC Settings ScreenFunctions and set values Initial value Memo Memo OFF PriorityMotion BLCAuto ColourMode AUXVideo Adjust Screen Mode Select Screen Terminal Motion ZoomMAX Alarm Time Motion Detect ScreenArea Edit Maintenance Screen Factory Settings ScreenCommunication Screen BLC Editting Screen EDIT1 screen is brought upSides having marks can be changed Manual Adjustment of White Balance Selected character is displayed flashing on and off Camera Title SettingScreen returns to Mode Select Then, the Camera Title screen is brought upMotion Detect screen Setting the Motion Detect FunctionSetting screen is brought up Select the item Area Edit onSet the B&W Item to Auto Output of Black-White/Color switching signalSet the B&W item to AUX B&W/COLOR Mode screen appearsCCD Spot screen will be dis- played White spot compensationOperation method Confirm that the cursor is at the itemOUT SpecificationsDimensions Unit mm Video OUTTK-C1430 Colour Video Camera