JVC KY-F70 manual Explanation of terminals, Remoter terminal Metal 10-pin, female, E12

Page 12

1. Introduction (continued)

Explanation of terminals

Power terminal (Mini DIN 8-pin, female) Lens terminal (Metal 12-pin, female)

7

8 6

5 3

24

@@ @ @ @ @ 1

Pin no.

Signal name

1NC

2GND

3NC

4NC

5GND

612V

7NC

812V

Remoter terminal (Metal 10-pin, female)

8 1

72

109

63

5 4

	9	10	1
	9		1
	8		2
	7		3
	6		4
	12	5	11
Pin no.		Signal name

1	NC

2

3	GND

4	NC

5	IRIS CONTROL

6	12V DC

7	IRIS POSITION

8	IRIS AUTO /MANU

9	NC

10	NC

11	NC

12	NC

Pin no.	Signal name

1	A. WHITE active Zi=22k Ω

2	FREEZE L active Zi=100k Ω

3	WEN L active Zo=100 Ω 3V(p-p)

4	FLASH

5	SEND (PRINT)

6	RS-SDI

7	RS-SDO

8	GND

9	12V

10	OPERATION

	Terminal	I/O	Conditions
	name	I/O	Conditions
	name

	FREEZE	IN	• Contact point
		• 5V CMOS	recommended
		• Schmidt Trigger	• Rated voltage:
		• Pull-up to 5V at	5.3V
		100k Ω	• H level: 3.5 ~ 5.0V
		• Input capacity	• L level: 0 ~ 0.8V
		0.1 μF	• CMOS (5V): OK
			• TLL not possible

	WEN	OUT	• Output only when
		• 3.3V (p-p)	in the SXGA mode
		negative polarity

	FLASH	OUT	• Rated current:
		• Open collector	150mA
			• Rated voltage:
			12V

E12

Image 12

Contents Illustration with optional lens attachment This instruction book is made from 100% recycled paperSafety Precautions Varning Table of Contents Characters and symbols used in this instruction book MemoFeatures Accessories and attachmentsIntroduction Line and patterns may appear distorted when recorded Phenomena unique to CCDPart names and their functions Front and bottomRear E10 ModeVentilation hole This lamp lights when the power of the main unit is on E11Used to connect the lens cable Mounting the lens Explanation of terminals Remoter terminal Metal 10-pin, femaleE12 E13 For the power supply, always use the AA-P700 AC adapter Before recordingBasic system E14E15 AC adapterMO disk drive Model name AdapterInstall E16Screws Female Lens remote control Mounting the lensE17 Camera head Male Thread section Mount clamp ring LensConnecting the power Clamp filter Attached power supply cableE18 AC adapterConnecting a monitor E19Monitor terminal Connecting an MO drive unit E20Scsi Do not set the ID of the MO drive side to other thanConnecting a printer Dip switchesE21 Scsi Set the ID of the printer side to other thanMounting the camera Mounting methodChanging the camera mounting bracket position E22Fall prevention wire chain 6mm Camera head Fall preventionE23 E24 Minal on the rear of the main unitSet to OFF Set to onMenu settings VGA mode settingsLens settings VGA mode and lens settings are made from the menu screenTime and date settings Time Adjust screenE26 Play menu screenE27 OK display screenMonitor adjustment Turn the main unit power on Adjust the video monitorSet using the main unit dip switches Monitor settings E28Focus adjustment E29Press the Menu button to return to the normal screen White balance adjustment E30REC Menu screen Menu item Set value White Balance screenE31 Auto white in operationAuto white operation completed White shading adjustment E32REC Menu screen E33 Basic operations Recording images to the main unit memoryE34 Freeze displayReturning to the REC mode Press the Mode button to enter the Play modePlaying back images from the memory E35Saving images from the memory to an MO disk E36Set to either the Freeze or Play mode Outputting images from the memory to a printerUse a printer with an Scsi input terminal E37Clearing images from the memory E38Video Memory Clear E39 Memory clearedVarious recording methods Recording a PC monitorE40 System Setting screen Outputting negative imagesE41 Timing chart Sxga mode Synchronizing flash and FreezeE42 High speed shutter onlyAbout ALC and EEI operations E43Menu screen settings Menu screen flowE44 E45 Exposure screenFreeze screen Process screenSetting procedure REC normal menu screenE46 REC normal menu screen Menu item Set valueAbout the submenu screens of the normal REC menu Play menu screenREC quick menu screen E47Exposure screen E48E49 E50 White Balance screen E51Mode OFF E52Shading Level GFreeze screen Process 1/3 screenE53 @ADJUST set when changing the gamma curve E54Gamma Used to set whether the gamma curve to determineProcess 2/3 screen E55Flare R Flare BE56 ColorMatrix Standard valueSystem Setting screen E57E58 Menu screen of the Play mode E59Send Prioryty Video ME.MORYREC mode quick menu screen E60Menu item TorSensitivity can be changed using the Level Submenu item Sensitivity can be changed when the sensitivity modeE61 Resetting settings Menu Reset screen SET buttonResetting E62E63 Press the Menu once more to return to the normal screenConnecting to a PC Camera remote control softwareCompatible systems E64Printer Flash Freeze switch E65AC adapter Analog RGB, WEN, Hs, Vs, RS-232C Specifications OthersE66 External dimensions unit mm E67Inch screw SL96172