Panasonic AW-E560 manual CA28T103 Connection Procedure

Page 25

■CA28T103 CONNECTION PROCEDURE

•Connecting Receiver and Control Cable CA28T103

•The control cable CA28T103 is provided with a circuit board and spacers.

•Assemble the circuit board and spacer with the receiver WV-RC100 (WV-RC150), and connect the control cable to that circuit board.

(1)Remove the two screws on the connector board shown from inside the receiver.

(2)Fit the two spacers on the connector board and fasten the circuit board with the screws removed in Step (1).

Spacer

Screws

Circuit board, an accessory to the cable

-23-

Image 25

Contents AW-E560 Lightning flash with arrowhead sym Contents Preface FeaturesAGC Special Notes on Operation Donts PrecautionsPage Top View Bottom View Front View Major Operating Controls and Their FunctionsItem Switch ITEM/AWC SwitchUp Switch UP/ABC Down Switch DOWN/BARIris Connector Iris Video Output Connector Video OUTZoom/Focus Connector ZOOM/FOCUS Power Indicator Remote Connector RemoteDC Input Connector EXT DC Control Connector Control Video/RGB Output Connector VIDEO/RGBLens Mounting 15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFFIris Gain Control in a Lens Flange Back AdjustmentConnections Connection of Device with a Composite Input ConnectorConnector pin layout How to assemble the power cableWires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras Connection of Computer Interface Adaptor PC Mode SystemCA20TBNC Connection Procedures for Cable KIT WV-CA28T10DC12V CA28T103 Connection Procedure Page Color temperature and adjustment of white balance AdjustmentAdjustment with the RCU RCB Manual White Balance Setting Automatic Tracking White Balance Setting ATWBlack Balance Adjustment Adjustment by Camera Reset to 3200K or 5600K White BalanceAdjustment with RCU or RCB Total Pedestal Level AdjustmentHorizontal Phase Control GEN-LOCK AdjustmentPhase Coarse Fine RET END Color Phase AdjustmentOperation Mode Setting Operation Mode SettingSettings CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Setup Memory Menu Item SettingSetup State Setup Data Screen Camera AloneIris Control Setting Iris MANU, Auto Scene 2 Scene How to Read Screens Initial SET Menu SettingHow to Set Initial Set MemoryInitial Set Screen Initial Set StateRCU RCB Camera AloneTotal Pedestal Adjustment T PED Red gain adjustment R Gain Blue gain adjustment B Gain2Painting Setting Painting ON/OFF 3AUTO IRIS/AGC/ELC Level Adjustment LevelFrame Auto Iris ADJ ON/ADJ OFFOFF @6Output Signal Setting 2 Output SEL2 Y/C, Composite @5Output Signal Setting@8Camera ID on/off setting Camera ID ON/OFF @9Time Date on/off setting Time Date ON/OFFSETUP/INITIAL Set Memory Reset User Setting User Setup Menu SettingScene File Memory User Set ScreensCamera Alone Camera with RCU RCB #2White Clip Level Setting White Clip 95% to 110% #1Knee Compensation Level Setting Knee Point 88% to 98%#4Detail Band Level Setting DTL Band 1 to #5Noise Suppress Compensation Level Setting Noise SUP 0 toGammanor YES UP SW No Down SW NOW Reset User a Memory User Set Memory ResetCamera Installation Camera ID Setting Camera ID SettingCamera ID UP SW ← → Down SW Item SW Camera ID Display Position Camera ID Display Position SettingCamera ID Position Set Screen Time/Date Setting TIME/DATE SettingTime/Date Set Screen Camera Alone Time/Date Display Position Set Screen Time/Date Display Position SettingTime/Date Display Position Iris Auto Manu Setup Menu Shutter OFF ELC White BAL Range of SETUP/INITIAL SET and Their Initial ValuesPurpose Indoor AGC High AGC LOWScene User a User B Range of Scene FILE/USER SET and Their Initial ValuesGamma NOR Gamma SHT Knee Point White Clip Flare RSCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 Ntsc SpecificationsVBS, BB, HD, VD AUTO, ELCOptional Accessories Standard AccessoriesWV-RC700A WV-CB700AN1097-0 7J1A095A