Panasonic AW-E560 manual Auto Iris ADJ ON/ADJ OFF, Frame, Off

Page 42

!5Detecting Ratio Adjustment [PEAK/AVG]

The ratio of AUTO IRIS/AGC/ELC detected peak to average can be adjusted in a range of 9 steps.

!6AUTO IRIS Level Fine Adjustment Setting

[AUTO IRIS: ADJ ON/ADJ OFF]

When the mode is set to ADJ ON, fine adjustment of ALC/ AGC/ELC convergence level can be made with the iris VR control on the RCU (RCB) if the camera is used with an RCU (RCB) and the iris mode is set to AUTO in the SETUP menu.

!7Synchroscan Adjustment [SYNCHRO-SCAN: 1/525 to 253/ 525]

Shutter speed can be adjusted when the shutter speed mode is set to SYNCHRO in the SETUP menu. In shooting a monitor screen, for example, set the shutter speed mode is set to SYNCHRO and use this item for shutter speed adjustment so that horizontal bar noise will be reduced.

!8CCD Read Out Mode Setting [FLD/FRM: FIELD/

FRAME]

The position FIELD means CCD field storage. The position FRAME means frame storage, in which case vertical resolution increases.

FIELD: Set to this mode when shooting moving object

FRAME: Set to this mode when shooting still object

*It is recommended that the mode be normally kept at FIELD because, if the mode is set to FRAME, residual image will increase.

!9Gamma Correction ON/OFF Setting [GAMMA: ON,

OFF]

Gamma correction ON/OFF can be set.

*Gamma correction level can be set using a user set menu.

@02-Dimensional Lowpass Filter ON OFF Setting [2D LPF: ON, OFF]

2D lowpass filter ON/OFF can be set to reduce cross colors.

@1Color Bar Setting (COLOR BAR: 1, 2, 3, 4]

Color bars can be selected.

1:SMPTE color bar with 0.0% setup

2:SMPTE color bar with 7.5% setup

3:Full color bar with 0.0% setup

4:Full color bar with 7.5% setup

@2Horizontal Phase Adjustment [H PHASE]

Horizontal phase can be adjusted when a genlock sig- nal is supplied.

@3Sub Carrier Phase Coarse Adjustment [SC COARSE: 0°, 90°, 180°, 270°]

Coarse adjustment of sub carrier phase can be made when a genlock signal is supplied.

@4Sub Carrier Phase Fine Adjustment [SC FINE]

Fine adjustment of sub carrier phase can be made when a genlock signal is supplied.

-40-

Image 42

Contents AW-E560 Lightning flash with arrowhead sym Contents Features PrefaceAGC Special Notes on Operation Precautions DontsPage Major Operating Controls and Their Functions Top View Bottom View Front ViewUp Switch UP/ABC SwitchItem Switch ITEM/AWC Down Switch DOWN/BARVideo Output Connector Video OUT Iris Connector IrisZoom/Focus Connector ZOOM/FOCUS Remote Connector Remote Power IndicatorDC Input Connector EXT DC Video/RGB Output Connector VIDEO/RGB Control Connector Control15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFF Lens MountingFlange Back Adjustment Iris Gain Control in a LensConnection of Device with a Composite Input Connector ConnectionsHow to assemble the power cable Connector pin layoutWires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras PC Mode System Connection of Computer Interface AdaptorConnection Procedures for Cable KIT WV-CA28T10 CA20TBNCDC12V CA28T103 Connection Procedure Page Adjustment Color temperature and adjustment of white balanceAdjustment with the RCU RCB Automatic Tracking White Balance Setting ATW Manual White Balance SettingAdjustment with RCU or RCB Reset to 3200K or 5600K White BalanceBlack Balance Adjustment Adjustment by Camera Total Pedestal Level AdjustmentGEN-LOCK Adjustment Horizontal Phase ControlColor Phase Adjustment Phase Coarse Fine RET ENDOperation Mode Setting Operation Mode SettingSettings CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Setup State Menu Item SettingSetup Memory Setup Data Screen Camera AloneIris Control Setting Iris MANU, Auto Scene 2 Scene How to Set Initial SET Menu SettingHow to Read Screens Initial Set Memory Initial Set State Initial Set ScreenCamera Alone RCU RCB2Painting Setting Painting ON/OFF Red gain adjustment R Gain Blue gain adjustment B GainTotal Pedestal Adjustment T PED 3AUTO IRIS/AGC/ELC Level Adjustment LevelAuto Iris ADJ ON/ADJ OFF FrameOFF @8Camera ID on/off setting Camera ID ON/OFF @5Output Signal Setting@6Output Signal Setting 2 Output SEL2 Y/C, Composite @9Time Date on/off setting Time Date ON/OFFSETUP/INITIAL Set Memory Reset Scene File Memory User Setup Menu SettingUser Setting User Set ScreensCamera Alone Camera with RCU RCB #4Detail Band Level Setting DTL Band 1 to #1Knee Compensation Level Setting Knee Point 88% to 98%#2White Clip Level Setting White Clip 95% to 110% #5Noise Suppress Compensation Level Setting Noise SUP 0 toGammanor User Set Memory Reset YES UP SW No Down SW NOW Reset User a MemoryCamera Installation Camera ID Setting Camera ID SettingCamera ID UP SW ← → Down SW Item SW Camera ID Display Position Setting Camera ID Display PositionCamera ID Position Set Screen TIME/DATE Setting Time/Date SettingTime/Date Set Screen Camera Alone Time/Date Display Position Setting Time/Date Display Position Set ScreenTime/Date Display Position Purpose Indoor Range of SETUP/INITIAL SET and Their Initial ValuesIris Auto Manu Setup Menu Shutter OFF ELC White BAL AGC High AGC LOWGamma NOR Gamma SHT Knee Point White Clip Range of Scene FILE/USER SET and Their Initial ValuesScene User a User B Flare RSCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 VBS, BB, HD, VD SpecificationsNtsc AUTO, ELCWV-RC700A Standard AccessoriesOptional Accessories WV-CB700AN1097-0 7J1A095A