Panasonic AW-E560 manual

Page 26

(3)	Disconnect the connector from connector CN4 on the	(5) Connect the control cable CA28T103 to connector
	process circuit board, and connect it to connector	CN1 on the circuit board.
	CN2 on the circuit board mounted. (Cut off or remove
	the wire band.)
(4)	Connect the lead from the circuit board to the ALARM
	DC COM terminal.

ALARM DC COM terminal

Process circuit board

Control cable

Connect the 28-pin end of it to the control ter- minal on the camera.

Circuit board, an accessory to the cable

-24-

Image 26

Contents AW-E560 Lightning flash with arrowhead sym Contents AGC FeaturesPreface Special Notes on Operation Precautions DontsPage Major Operating Controls and Their Functions Top View Bottom View Front ViewUp Switch UP/ABC SwitchItem Switch ITEM/AWC Down Switch DOWN/BARZoom/Focus Connector ZOOM/FOCUS Video Output Connector Video OUTIris Connector Iris DC Input Connector EXT DC Remote Connector RemotePower Indicator Video/RGB Output Connector VIDEO/RGB Control Connector Control15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFF Lens MountingFlange Back Adjustment Iris Gain Control in a LensConnection of Device with a Composite Input Connector ConnectionsHow to assemble the power cable Connector pin layoutWires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras PC Mode System Connection of Computer Interface AdaptorConnection Procedures for Cable KIT WV-CA28T10 CA20TBNCDC12V CA28T103 Connection Procedure Page Adjustment Color temperature and adjustment of white balanceAdjustment with the RCU RCB Automatic Tracking White Balance Setting ATW Manual White Balance SettingAdjustment with RCU or RCB Reset to 3200K or 5600K White BalanceBlack Balance Adjustment Adjustment by Camera Total Pedestal Level AdjustmentGEN-LOCK Adjustment Horizontal Phase ControlColor Phase Adjustment Phase Coarse Fine RET ENDSettings Operation Mode SettingOperation Mode Setting CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Setup State Menu Item SettingSetup Memory Setup Data Screen Camera AloneIris Control Setting Iris MANU, Auto Scene 2 Scene How to Set Initial SET Menu SettingHow to Read Screens Initial Set MemoryInitial Set State Initial Set ScreenCamera Alone RCU RCB2Painting Setting Painting ON/OFF Red gain adjustment R Gain Blue gain adjustment B GainTotal Pedestal Adjustment T PED 3AUTO IRIS/AGC/ELC Level Adjustment LevelOFF Auto Iris ADJ ON/ADJ OFFFrame @8Camera ID on/off setting Camera ID ON/OFF @5Output Signal Setting@6Output Signal Setting 2 Output SEL2 Y/C, Composite @9Time Date on/off setting Time Date ON/OFFSETUP/INITIAL Set Memory Reset Scene File Memory User Setup Menu SettingUser Setting User Set ScreensCamera Alone Camera with RCU RCB #4Detail Band Level Setting DTL Band 1 to #1Knee Compensation Level Setting Knee Point 88% to 98%#2White Clip Level Setting White Clip 95% to 110% #5Noise Suppress Compensation Level Setting Noise SUP 0 toGammanor User Set Memory Reset YES UP SW No Down SW NOW Reset User a MemoryCamera Installation Camera ID Camera ID SettingCamera ID Setting UP SW ← → Down SW Item SW Camera ID Position Set Screen Camera ID Display Position SettingCamera ID Display Position Time/Date Set Screen Camera Alone TIME/DATE SettingTime/Date Setting Time/Date Display Position Time/Date Display Position SettingTime/Date Display Position Set Screen Purpose Indoor Range of SETUP/INITIAL SET and Their Initial ValuesIris Auto Manu Setup Menu Shutter OFF ELC White BAL AGC High AGC LOWGamma NOR Gamma SHT Knee Point White Clip Range of Scene FILE/USER SET and Their Initial ValuesScene User a User B Flare RSCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 VBS, BB, HD, VD SpecificationsNtsc AUTO, ELCWV-RC700A Standard AccessoriesOptional Accessories WV-CB700AN1097-0 7J1A095A