Panasonic AW-E560 manual Time/Date Display Position Set Screen, Time/Date Display Position Setting

Page 55

■ How to Set
(1)	Select the date and time positions to change, or a
	command, using the item switch.
(2)	To change time/date, use the Up switch.
	The set value increases each time the Up switch is
	pressed. Stop pressing it when the desired figure
	appears.

■Time/Date Display Position Set Screen

	(If the Up switch is kept depressed, the figure increas-
	es rapidly.)
(3)	If the page switch is pressed when the cursor is at
	POSI, time/date display position is ready to be set.
(4)	To return to the INITIAL SET menu screen, move the
	cursor to RET, and press the page switch.
(5)	To return to the normal state, do the following steps.
	If the camera is used alone, move the cursor to END,

AW-E560

02-23-93 18:40

Camera ID display position

It cannot be over time/ date display.

Time/date display (blinking)

and press the page switch.

If the camera is used with an RCU (RCB), set the user

set switch to OFF.

■ Time/Date Display Position

Time/date display position can be set as desired.

■Time/Date Display Position Setting

(1)Set time/date.

(2)Move the cursor to POSI, and press the page switch. Time/date display position is ready to be set, and its screen appears on the monitor.

Time/date display position can be set at the camera head or RCU (RCB).

■How to Set

(1)Move the set time/date display position using the item switch, Up switch, or Down switch.

Item switch: To move the cursor 1 line down

Up switch: To move the cursor 1 position left

Down switch: To move the cursor 1 position right

UP SW ← → DOWN SW

↓

ITEM SW

-53-

Image 55

Contents AW-E560 Lightning flash with arrowhead sym Contents Preface FeaturesAGC Special Notes on Operation Donts PrecautionsPage Top View Bottom View Front View Major Operating Controls and Their FunctionsDown Switch DOWN/BAR SwitchItem Switch ITEM/AWC Up Switch UP/ABCIris Connector Iris Video Output Connector Video OUTZoom/Focus Connector ZOOM/FOCUS Power Indicator Remote Connector RemoteDC Input Connector EXT DC Control Connector Control Video/RGB Output Connector VIDEO/RGBLens Mounting 15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFFIris Gain Control in a Lens Flange Back AdjustmentConnections Connection of Device with a Composite Input ConnectorConnector pin layout How to assemble the power cableWires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras Connection of Computer Interface Adaptor PC Mode SystemCA20TBNC Connection Procedures for Cable KIT WV-CA28T10DC12V CA28T103 Connection Procedure Page Color temperature and adjustment of white balance AdjustmentAdjustment with the RCU RCB Manual White Balance Setting Automatic Tracking White Balance Setting ATWTotal Pedestal Level Adjustment Reset to 3200K or 5600K White BalanceBlack Balance Adjustment Adjustment by Camera Adjustment with RCU or RCBHorizontal Phase Control GEN-LOCK AdjustmentPhase Coarse Fine RET END Color Phase AdjustmentOperation Mode Setting Operation Mode SettingSettings CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Setup Data Screen Camera Alone Menu Item SettingSetup Memory Setup StateIris Control Setting Iris MANU, Auto Scene 2 Scene Initial Set Memory Initial SET Menu SettingHow to Read Screens How to SetInitial Set Screen Initial Set StateRCU RCB Camera Alone3AUTO IRIS/AGC/ELC Level Adjustment Level Red gain adjustment R Gain Blue gain adjustment B GainTotal Pedestal Adjustment T PED 2Painting Setting Painting ON/OFFFrame Auto Iris ADJ ON/ADJ OFFOFF @9Time Date on/off setting Time Date ON/OFF @5Output Signal Setting@6Output Signal Setting 2 Output SEL2 Y/C, Composite @8Camera ID on/off setting Camera ID ON/OFFSETUP/INITIAL Set Memory Reset User Set Screens User Setup Menu SettingUser Setting Scene File MemoryCamera Alone Camera with RCU RCB #5Noise Suppress Compensation Level Setting Noise SUP 0 to #1Knee Compensation Level Setting Knee Point 88% to 98%#2White Clip Level Setting White Clip 95% to 110% #4Detail Band Level Setting DTL Band 1 toGammanor YES UP SW No Down SW NOW Reset User a Memory User Set Memory ResetCamera Installation Camera ID Setting Camera ID SettingCamera ID UP SW ← → Down SW Item SW Camera ID Display Position Camera ID Display Position SettingCamera ID Position Set Screen Time/Date Setting TIME/DATE SettingTime/Date Set Screen Camera Alone Time/Date Display Position Set Screen Time/Date Display Position SettingTime/Date Display Position AGC High AGC LOW Range of SETUP/INITIAL SET and Their Initial ValuesIris Auto Manu Setup Menu Shutter OFF ELC White BAL Purpose IndoorFlare R Range of Scene FILE/USER SET and Their Initial ValuesScene User a User B Gamma NOR Gamma SHT Knee Point White ClipSCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 AUTO, ELC SpecificationsNtsc VBS, BB, HD, VDWV-CB700A Standard AccessoriesOptional Accessories WV-RC700AN1097-0 7J1A095A