Panasonic AW-E560 manual Iris Control Setting Iris MANU, Auto

Page 36

1Gain Up Control Setting [GAIN: AGC LOW, AGC HIGH, 0DB, 9DB, 18DB]

When the mode is set to AGC LOW or AGC HIGH, the AGC with a maximum gain increase of about 9 dB/18 dB operates to control gain up and automatically reg- ulate the amount of light.

Normally, the mode should be set to 0DB. If a suffi- cient video output is not obtained in shooting a dark object even when the iris is fully opened, set the mode

to the 9DB or 18DB position.

•AGC convergence level, photometric method, and detecting ratio can be set by INITIAL SET menu.

Note:

In using the AGC, it may not function when the iris switch is in the manual position on the lens with auto iris ON in the SETUP menu.

2Iris Control Setting [IRIS: MANU, AUTO]

When the mode is set to AUTO, lens iris is controlled automatically with lens iris is A (auto) position.

•Auto iris convergence level, photometric method, and detecting ratio can be set by INITIAL SET menu.

Note:

When the iris control is set to AUTO in this menu, set the iris switch on the lens to the A (auto) posi- tion. If the iris is set to MANU in this menu, set the iris switch on the lens to the M (manual) position.

3Electronic Shutter Speed Setting [SHUTTER: ELC, OFF, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, SYNCHRO]

When the mode is set to ELC, the electronic shutter speed is automatically controlled to regulate the amount of light.

When the mode is set to OFF, the electronic shutter is turned off. The mode is set to between 1/100 and 1/10000 represent respective shutter speeds.

Set the mode to SYNCHRO (synchro scan) for fine adjustment of shutter speed.

*Refer to the table below for the relative light quantity required for each setting of shutter speed and synchro scan.

Shutter Speed	Synchro Scan	Required Light Ratio

OFF	--	1

1/100	159/525	2

1/250	63/525	4

1/500	31/525	8

1/1000	15/525	16

1/2000	7/525	32

1/4000	3/525	64

1/10000	1/525	160

*ELC convergence level, photometric method, and detecting ratio can be set by INITIAL SET menu. When the mode is set to SYNCHRO, shutter speed can be set by INITIAL SET menu.

Note: If the camera is used with an RCU (RCB), shut- ter speeds of 1/250, 1/2000, 1/4000, 1/10000 can- not be selected.

-34-

Image 36

Contents AW-E560 Lightning flash with arrowhead sym Contents Features PrefaceAGC Special Notes on Operation Precautions DontsPage Major Operating Controls and Their Functions Top View Bottom View Front ViewSwitch Item Switch ITEM/AWCUp Switch UP/ABC Down Switch DOWN/BARVideo Output Connector Video OUT Iris Connector IrisZoom/Focus Connector ZOOM/FOCUS Remote Connector Remote Power IndicatorDC Input Connector EXT DC Video/RGB Output Connector VIDEO/RGB Control Connector Control15. G/L Signal 75-ohm ON/OFF Switch 75Ω ON/OFF Lens MountingFlange Back Adjustment Iris Gain Control in a LensConnection of Device with a Composite Input Connector ConnectionsHow to assemble the power cable Connector pin layoutWires Connection of a Remote Controller RCU and a Studio Cable Multiplex adaptor WV-PS550 Connection of a Remote Control BOX RCB Connection with Multiple Cameras PC Mode System Connection of Computer Interface AdaptorConnection Procedures for Cable KIT WV-CA28T10 CA20TBNCDC12V CA28T103 Connection Procedure Page Adjustment Color temperature and adjustment of white balanceAdjustment with the RCU RCB Automatic Tracking White Balance Setting ATW Manual White Balance SettingReset to 3200K or 5600K White Balance Black Balance Adjustment Adjustment by CameraAdjustment with RCU or RCB Total Pedestal Level AdjustmentGEN-LOCK Adjustment Horizontal Phase ControlColor Phase Adjustment Phase Coarse Fine RET ENDOperation Mode Setting Operation Mode SettingSettings CURRMODE1/SCENE1 SCENE2 SCENE3 User a User B Menu Item Setting Setup MemorySetup State Setup Data Screen Camera AloneIris Control Setting Iris MANU, Auto Scene 2 Scene Initial SET Menu Setting How to Read ScreensHow to Set Initial Set MemoryInitial Set State Initial Set ScreenCamera Alone RCU RCBRed gain adjustment R Gain Blue gain adjustment B Gain Total Pedestal Adjustment T PED2Painting Setting Painting ON/OFF 3AUTO IRIS/AGC/ELC Level Adjustment LevelAuto Iris ADJ ON/ADJ OFF FrameOFF @5Output Signal Setting @6Output Signal Setting 2 Output SEL2 Y/C, Composite@8Camera ID on/off setting Camera ID ON/OFF @9Time Date on/off setting Time Date ON/OFFSETUP/INITIAL Set Memory Reset User Setup Menu Setting User SettingScene File Memory User Set ScreensCamera Alone Camera with RCU RCB #1Knee Compensation Level Setting Knee Point 88% to 98% #2White Clip Level Setting White Clip 95% to 110%#4Detail Band Level Setting DTL Band 1 to #5Noise Suppress Compensation Level Setting Noise SUP 0 toGammanor User Set Memory Reset YES UP SW No Down SW NOW Reset User a MemoryCamera Installation Camera ID Setting Camera ID SettingCamera ID UP SW ← → Down SW Item SW Camera ID Display Position Setting Camera ID Display PositionCamera ID Position Set Screen TIME/DATE Setting Time/Date SettingTime/Date Set Screen Camera Alone Time/Date Display Position Setting Time/Date Display Position Set ScreenTime/Date Display Position Range of SETUP/INITIAL SET and Their Initial Values Iris Auto Manu Setup Menu Shutter OFF ELC White BALPurpose Indoor AGC High AGC LOWRange of Scene FILE/USER SET and Their Initial Values Scene User a User BGamma NOR Gamma SHT Knee Point White Clip Flare RSCENE/USER File and Their Initial Value MODE2 SCENE/USER File Initial Value MODE3 SCENE/USER File and Their Initial Value MODE4 Specifications NtscVBS, BB, HD, VD AUTO, ELCStandard Accessories Optional AccessoriesWV-RC700A WV-CB700AN1097-0 7J1A095A