Axis Communications Q6034 user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 47

AXIS Q6034 PTZ Dome Network Camera

System Options

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS, on page 41. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings, on page 50.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are conﬁgured under System Options > Network > RTP.

The RTP port range deﬁnes the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

The Axis product supports SD cards with the following ﬁle systems:

•ext4 — recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.

•vFAT — most SD cards are pre-formatted with vFAT when purchased.

If required, the SD card can be re-formatted to the desired ﬁle system. To format the SD card:

1.Insert the SD card in the SD card slot.

2.Go to System Options > Storage and click SD Card.

47

Image 47

Contents Axis Q6034 PTZ Dome Network Camera Intellectual Property Rights SafetyAbout this Document LiabilityLearn More Axis Q6034 PTZ Dome Network Camera Table of ContentsSymptoms, Possible Causes and Remedial Actions For technical speciﬁcations, see ConnectorsHardware Overview Hardware OverviewColor Indication LED IndicatorsMidspan LED Indicators Start a browser Internet Explorer, Firefox, Safari Accessing the ProductAccessing the Product Access from a BrowserClick Create self-signed certiﬁcate Access from the InternetSet the Root Password Network TCP/IP AdvancedAxis Media Control viewer toolbar Live ViewControls on the Live View AMC Audio Controls PTZ ControlsAxis Q6034 PTZ Dome Network Camera Axis Media Control AMC How to Stream H.264Media Streams Media StreamsQuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Accessing Audio StreamsBasic Setup Setting Up the ProductSetting Up the Product Pixel Counter Video and AudioVideo and Audio Video Stream264 Click Save to apply the new settingsStream Proﬁles ImageWhite Balance Camera SettingsExposure Settings Image AppearanceGo to Video & Audio Video Stream and select the Image tab Image SettingsOverlay Overlay ImageAudio Input Audio SettingsPrivacy Mask Audio ModesG711 G726 Audio ClipsAudio Output Axis Q6034 PTZ Dome Network Camera Live View Conﬁg Default Viewer for BrowsersLive View Conﬁg Output Buttons Viewer SettingsGo to Setup Live View Conﬁg User Deﬁned LinksAxis Q6034 PTZ Dome Network Camera Autotracking Preset PositionsPTZ Pan Tilt Zoom PTZ Pan Tilt ZoomMax Limits ConﬁgurationExclude Areas Guard Tour GatekeeperLimits Osdi ZonesAdvanced Tour RecordingControls Operator Same as administrator but with lower priorityControl Queue Motion Detection Set Up Motion Detection WindowsDetectors DetectorsMotion Detection Parameters Audio DetectionApplications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RuleConvert Event Types to Action Rules PTZ ControlGo to Events Recipients and click Add RecipientsSchedules Recipient Use with actionGo to Events Recurrences and click Add RecurrencesContinuous Recording RecordingsRecordings Recording ListAxis Q6034 PTZ Dome Network Camera Users System OptionsSystem Options SecurityAudio Support Date & TimeIeee IPv6 Address Conﬁguration Basic TCP/IP SettingsNetwork IPv4 Address ConﬁgurationAdvanced TCP/IP Settings NAT traversal port mapping for IPv4 Link-Local IPv4 AddressSmtp email QoS Quality of ServiceBonjour StorageUPnPTM RTP/H.264Go to System Options Storage Click Network Share Ports & DevicesNetwork Share PortsSupport MaintenancePlain Conﬁg Reset to Factory Default SettingsScripting File Upload192.168.0.90 Checking the Firmware TroubleshootingTroubleshooting Emergency Recovery ProcedureProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Problems with the H.264 format Product is accessible locally but not externallyOverlay image is not displayed Video and image problems, generalSetup Video & Audio Camera Settings No images displayed on webMotion Detection triggers unexpectedly Problems uploading ﬁlesSettings Storage and disk management problemsTechnical Speciﬁcations Technical SpeciﬁcationsConnectors Installation aidMaintenance PowerMulti-Connector Cable sold separately With the load, for protection against voltage transients Function Pin SpeciﬁcationsTo +40 V DC Max voltage = +40 V DCPerformance Considerations Connection diagramDC power input Axis Q6034 PTZ Dome Network Camera M1.6