Bosch Appliances VOT-320 manual Remote port, Video output, Decoder, SSL encryption, Auto-connect

Page 55

VOT-320

Configuration using a Web browser en 55

 

 

Remote port

Depending on the network configuration, select a browser port here. The ports for HTTPS connections will be available only if the On option is selected in the SSL encryption parameter.

Video output

If you know which unit is being used as the receiver, you can select the analog video output to which the signal should be switched. If the destination unit is unknown, it is advisable to select the First available option. In this case, the image is placed on the first free video output. This is an output on which there is no signal. The connected monitor only displays images when an alarm is triggered. If you select a particular video output and a split image is set for this output on the receiver, you can also select from Decoder the decoder in the receiver that is to be used to display the alarm image.

NOTICE!

Refer to the destination unit documentation concerning image display options and available video outputs.

Decoder

Select a decoder of the receiver to display the alarm image. The decoder selected has an impact on the position of the image in a split screen. For example, you can specify that the upper-right quadrant should be used to display the alarm image on a VIP XD by selecting Decoder 2.

SSL encryption

The data for the connection, for example the password, can be securely transmitted with SSL encryption. If you have selected the On option, only encrypted ports are offered in the Remote port parameter.

NOTICE!

Please note that the SSL encryption must be activated and configured at both ends of a connection. This requires the appropriate certificates to be uploaded onto the VOT-320 (see Section SSL certificate, page 79).

You can activate and configure encryption of the media data (video and metadata) on the Encryption page (see Section 5.38 Advanced Mode: Encryption, page 77).

Auto-connect

Select the On option to automatically re-establish a connection to one of the previously specified IP addresses after each reboot, after a connection breakdown or after a network failure.

NOTICE!

In the default setting, Stream 1 is transmitted for automatic connections. Bear this fact in mind when assigning the profile (see Section 5.17 Advanced Mode: Encoder Profile, page 40).

Bosch Sicherheitssysteme GmbH

Installation and Operating Manual

DOC V4.5 2010.09

Image 55
Contents VOT-320 Page Table of Contents Operation Maintenance and upgradesAppendix Camera 104 Detector Protocols/standards 105 Specifications 104Glossary 106 Index 111 Intended use PrefaceAbout this manual Conventions in this manualRating plate EU DirectivesInstallation and operation Safety informationElectric shock hazard 3Maintenance and repair Parts included Product descriptionAdditional operational requirements Additional configuration requirementsSystem requirements General requirementsOverview of functions Snapshots Remote controlTamper detection and video content analysis BackupHttps SummaryControls and displays on the camera module Connections on the camera module 1Preparations 4Installation2Mounting En Installation Data interface 3ConnectionsNetwork Pin EIA/TIA-568-A EIA/TIA-568-BPan/tilt connection Alarm inputsRelay outputs Power supply 4Power on/power offSD slot Installing the program Adjusting the lens only Wfov lensesFinal assembly 7Setup using Bosch Video ClientAdditional parameters System requirements Configuration using a Web browser1Connecting Installing Mpeg ActiveXMaximum number of connections Establishing the connectionProtected camera Configuration menuProtected network Navigation Starting configurationMaking changes Password Basic Mode Device AccessCamera name Time server IP address Basic Mode Date/TimeConfirm password Device date / Device time / Device time zoneGateway address Basic Mode NetworkIP address Subnet maskBasic Mode Encoder Basic Mode System Overview Basic Mode RecordingCamera ID Advanced Mode IdentificationInitiator extension Advanced Mode Password Device time zone Advanced Mode Date/TimeDate format Device date / Device timeCamera name stamping Advanced Mode Display StampingTime stamping Advanced Mode Appearance Advanced Mode Livepage Functions Advanced Mode Logging Advanced Mode Encoder Profile Advanced Mode Picture SettingsFile for system log Target bit rate Profile nameMaximum bit rate Encoding interval Video resolutionExpert Settings Default264 BP+ bit-rate-limited Advanced Mode Encoder StreamsMP SD Picture quality PropertyJpeg stream Max. frame rateDevice manager Advanced Mode Storage ManagementLocal Media Activating and configuring storage mediaRecording media ISCSI MediaDeactivating storage media Formatting storage mediaStream profile settings Advanced Mode Recording ProfilesAlarm stream Settings for selected streamsPre-alarm time Post-alarm timeExport to FTP Advanced Mode Retention TimeAlarm input / Motion/Audio alarm / Video loss alarm Virtual alarmAdvanced Mode Recording Scheduler Activating the recording HolidaysDeleting holidays Time periodsAdvanced Mode Alarm Connections Advanced Mode Recording StatusCannot change any of these settings Destination IP address Connect on alarmDestination password Number of destination IP addressSSL encryption Remote portVideo output DecoderAdvanced Mode VCA Advanced Mode VCA profiles Analysis type VCA configurationAlarm status Aggregation time sDebounce time 1 s MOTION+ only Motion detector MOTION+ onlySensitivity MOTION+ only Minimum object size MOTION+ onlyScene too noisy Advanced Mode VCA ScheduledHolidays Trigger Advanced Mode VCA Event triggeredAdvanced Mode Alarm E-Mail Destination address FormatStandard with Jpeg Attach Jpeg from cameraAdvanced Mode Alarm Task Editor Alarm input Advanced Mode Alarm InputsAdvanced Mode Relay You can configure the alarm inputs of the VOT-320Idle state Operating modeVideo alarm Motion alarmAdvanced Mode COM1 Advanced Mode Network DNS server address Automatic IP assignmentHttp browser port RCP+ port Interface mode ETHEnable DynDNS Https browser portForce registration now Enter the password you registered at DynDNS.org hereUser name Enter the user name you registered at DynDNS.org hereSnmp Advanced Mode AdvancedIdentity AuthenticationSnmp host address / 2. Snmp host address Snmp trapsEnable Advanced Mode MulticastMulticast Address Advanced Mode FTP Posting Advanced Mode Maintenance Advanced Mode EncryptionUpload ConfigurationDownload Maintenance log Advanced Mode LicensesSSL certificate Advanced Mode System Overview Function test Operation with Microsoft Internet Explorer OperationVOT-320 Operation en Image selection 2The LivepageDisplay stamping View Control Triggering relay Digital I/OSystem Log / Event Log Running recording program Image resolutionSaving snapshots Recording video sequencesSelecting recordings RecordingsExporting recordings Buttons Controlling a playbackSlide controls Hardware connections between video servers ConnectingBookmarks Connecting with a terminal program Connecting on alarmClosing the connection with a terminal program 8Operation using software decoders Testing the network connection Maintenance and upgradesCamera reset Export limitations 3Fuse replacementRepairs Transfer and disposal8Appendix 1TroubleshootingGeneral malfunctions Firmware upload failed Repeat firmware upload Flashes red Connect LEDLink and ACT opening B Malfunctions with iSCSI connections4LEDs Connect opening aNetwork connection 5Processor load7Serial interface PT control upper and lower 5-pin terminal blocks Power supply upper 2-pin terminal blockTerminal blocks Window defroster lower 2-pin terminal blockSerial interface upper 6-pin terminal block Pin No Contact RS-232 mode RS-422 mode RS-485 modeData terminal Configuring the terminalCommand inputs Communication with terminal programAssigning an IP address RebootCopyrights Camera SpecificationsDetector Ntsc 3Protocols/standardsGlossary Icmp GbicGOP HttpMIB LANLUN MACSnia RTPRtsp SFPWide Field Of View, see FOV WANSee Wide Area Network WfovEprom IndexRadius VOT-320 Index en En Index Page Bosch Sicherheitssysteme GmbH