Bosch Appliances VOT-320 manual Advanced Mode Advanced, Snmp

Page 73

VOT-320Configuration using a Web browser en 73

5.35

Advanced Mode: Advanced

The settings on this page are used to implement advanced settings for the network. Some changes only take effect after the camera is rebooted. In this case, the Set button changes to Set and Reboot.

1.Make the desired changes.

2.Click the Set and Reboot button. The VOT-320 is rebooted and the changed settings are activated.

SNMP

The VOT-320 supports the SNMP V2 (Simple Network Management Protocol) for managing and monitoring network components, and can send SNMP messages (traps) to IP addresses. The camera supports SNMP MIB II in the unified code. If you wish to send SNMP traps, enter the IP addresses of one or two required target devices here.

If you select On for the SNMP parameter and do not enter an SNMP host address, the VOT-320 does not send the SNMP traps automatically, but only replies to SNMP requests. If you enter one or two SNMP host addresses, SNMP traps are sent automatically. Select Off to deactivate the SNMP function.

Bosch Sicherheitssysteme GmbH

Installation and Operating Manual

DOC V4.5 2010.09

Image 73
Contents VOT-320 Page Table of Contents Operation Maintenance and upgradesAppendix Camera 104 Detector Protocols/standards 105 Specifications 104Glossary 106 Index 111 About this manual PrefaceConventions in this manual Intended useRating plate EU DirectivesInstallation and operation Safety informationElectric shock hazard 3Maintenance and repair Parts included Product descriptionSystem requirements Additional configuration requirementsGeneral requirements Additional operational requirementsOverview of functions Tamper detection and video content analysis Remote controlBackup SnapshotsHttps SummaryControls and displays on the camera module Connections on the camera module 1Preparations 4Installation2Mounting En Installation Network 3ConnectionsPin EIA/TIA-568-A EIA/TIA-568-B Data interfacePan/tilt connection Alarm inputsRelay outputs Power supply 4Power on/power offSD slot Final assembly Adjusting the lens only Wfov lenses7Setup using Bosch Video Client Installing the programAdditional parameters 1Connecting Configuration using a Web browserInstalling Mpeg ActiveX System requirementsMaximum number of connections Establishing the connectionProtected camera Configuration menuProtected network Navigation Starting configurationMaking changes Password Basic Mode Device AccessCamera name Confirm password Basic Mode Date/TimeDevice date / Device time / Device time zone Time server IP addressIP address Basic Mode NetworkSubnet mask Gateway addressBasic Mode Encoder Basic Mode System Overview Basic Mode RecordingCamera ID Advanced Mode IdentificationInitiator extension Advanced Mode Password Date format Advanced Mode Date/TimeDevice date / Device time Device time zoneCamera name stamping Advanced Mode Display StampingTime stamping Advanced Mode Appearance Advanced Mode Livepage Functions Advanced Mode Logging Advanced Mode Encoder Profile Advanced Mode Picture SettingsFile for system log Target bit rate Profile nameMaximum bit rate Expert Settings Video resolutionDefault Encoding interval264 BP+ bit-rate-limited Advanced Mode Encoder StreamsMP SD Jpeg stream PropertyMax. frame rate Picture qualityDevice manager Advanced Mode Storage ManagementRecording media Activating and configuring storage mediaISCSI Media Local MediaDeactivating storage media Formatting storage mediaStream profile settings Advanced Mode Recording ProfilesPre-alarm time Settings for selected streamsPost-alarm time Alarm streamAlarm input / Motion/Audio alarm / Video loss alarm Advanced Mode Retention TimeVirtual alarm Export to FTPAdvanced Mode Recording Scheduler Deleting holidays HolidaysTime periods Activating the recordingAdvanced Mode Alarm Connections Advanced Mode Recording StatusCannot change any of these settings Destination password Connect on alarmNumber of destination IP address Destination IP addressVideo output Remote portDecoder SSL encryptionAdvanced Mode VCA Advanced Mode VCA profiles Alarm status VCA configurationAggregation time s Analysis typeSensitivity MOTION+ only Motion detector MOTION+ onlyMinimum object size MOTION+ only Debounce time 1 s MOTION+ onlyScene too noisy Advanced Mode VCA ScheduledHolidays Trigger Advanced Mode VCA Event triggeredAdvanced Mode Alarm E-Mail Standard with Jpeg FormatAttach Jpeg from camera Destination addressAdvanced Mode Alarm Task Editor Advanced Mode Relay Advanced Mode Alarm InputsYou can configure the alarm inputs of the VOT-320 Alarm inputVideo alarm Operating modeMotion alarm Idle stateAdvanced Mode COM1 Advanced Mode Network DNS server address Automatic IP assignmentHttp browser port Enable DynDNS Interface mode ETHHttps browser port RCP+ portUser name Enter the password you registered at DynDNS.org hereEnter the user name you registered at DynDNS.org here Force registration nowSnmp Advanced Mode AdvancedSnmp host address / 2. Snmp host address AuthenticationSnmp traps IdentityEnable Advanced Mode MulticastMulticast Address Advanced Mode FTP Posting Advanced Mode Maintenance Advanced Mode EncryptionUpload ConfigurationDownload Maintenance log Advanced Mode LicensesSSL certificate Advanced Mode System Overview Function test Operation with Microsoft Internet Explorer OperationVOT-320 Operation en Image selection 2The LivepageDisplay stamping View Control Triggering relay Digital I/OSystem Log / Event Log Saving snapshots Image resolutionRecording video sequences Running recording programSelecting recordings RecordingsExporting recordings Buttons Controlling a playbackSlide controls Hardware connections between video servers ConnectingBookmarks Connecting with a terminal program Connecting on alarmClosing the connection with a terminal program 8Operation using software decoders Testing the network connection Maintenance and upgradesCamera reset Repairs 3Fuse replacementTransfer and disposal Export limitations8Appendix 1TroubleshootingGeneral malfunctions Firmware upload failed Repeat firmware upload Flashes red Connect LED4LEDs Malfunctions with iSCSI connectionsConnect opening a Link and ACT opening BNetwork connection 5Processor load7Serial interface Terminal blocks Power supply upper 2-pin terminal blockWindow defroster lower 2-pin terminal block PT control upper and lower 5-pin terminal blocksSerial interface upper 6-pin terminal block Pin No Contact RS-232 mode RS-422 mode RS-485 modeCommand inputs Configuring the terminalCommunication with terminal program Data terminalAssigning an IP address RebootCopyrights Camera SpecificationsDetector Ntsc 3Protocols/standardsGlossary GOP GbicHttp IcmpLUN LANMAC MIBRtsp RTPSFP SniaSee Wide Area Network WANWfov Wide Field Of View, see FOVEprom IndexRadius VOT-320 Index en En Index Page Bosch Sicherheitssysteme GmbH