Cisco Systems CIVS-IPC-2630V manual Getting Started, Before You Begin

Page 13

C H A P T E R 2

Getting Started

This chapter provides instructions for installing and performing the initial setup of the Cisco Video Surveillance IP Camera. It also describes how to access the IP camera through a web browser so that you can configure it or view video from it, and how to perform other important tasks.

This chapter includes these topics:

•Before You Begin, page 2-1

•Installing the Cisco Video Surveillance 2630 IP Dome, page 2-2

•Performing the Initial Setup of the IP Camera, page 2-14

•Accessing the IP Camera Windows, page 2-16

•Adjusting the Video Image, page 2-17

•Powering the IP Camera On or Off, page 2-19

•Resetting the IP Camera, page 2-19

•Cleaning the IP Camera, page 2-19

Before You Begin

Before you install the IP camera, review these guidelines:

•The IP camera requires a twisted pair category 5 or higher network cable and a connection to a standard 10/100BaseT hub, router, or switch.

•The IP camera requires a 24 VAC power source that is isolated from the ground (floating output).

•If you are using an external speaker, microphone, input device, or output device, you must configure additional settings after installing and performing the initial set up of the IP camera before the external device can fully operate. For detailed information about these settings, see Chapter 3, “Configuring and Managing the IP Camera.”

•If you do not connect an external device (speaker, microphone, input device, output device, or control device) when you perform the following installation procedure, you can install any of these devices later.

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Cisco Video Surveillance 2630 IP Dome User Guide

	OL-24130-02	2-1

Image 13

Contents Americas Headquarters Cisco Video Surveillance 2630 IP Dome User GuideCisco Video Surveillance 2630 IP Dome User Guide Iii N T E N T SSnmp Window Organization OverviewVii Viii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2630 IP Dome Physical Details Overview IP Camera Overview Bottom of the 2630 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreparing for Installation Installing the Cisco Video Surveillance 2630 IP DomePreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Mounting with a Conduit Base ProcedureAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base Attaching the Camera to the Base Plate See -1 onCisco Video Surveillance 2630 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a PendantOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate 12 Attaching the Privacy Shield and Dome Performing the Initial Setup of the IP CameraProtocol//ipaddress Https//192.168.0.100 Accessing the IP Camera WindowsHttps//203.70.212.521024 Http//203.70.212.52Http//203.70.212.521024 Adjusting the Video Image13 Adjusting the Camera Lens on the 2630 IP Dome Resetting the IP Camera Powering the IP Camera On or OffCleaning the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Audio Window section See the Alarm I/O PortsSee the Privacy Region See the Focus/Zoom WindowSnmp Navigating the Configuration WindowsBasic Setup Window Setup WindowsDevice Settings Option DescriptionOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Controls section on Audio WindowDuplex Talk and Listen Focus/Zoom Window Privacy Region WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window Security WindowsInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsMail Setup Described in the Basic Setup Window section onPrimary Smtp Server Secondary Smtp ServerPrimary FTP Mail BodySecondary FTP Http NotificationSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window New Schedule Event ScheduleClear button Trigger EventAttachment Mail/FTP/HTTP Window section onSnmp Window Alarm Input Settings Alarm I/O Ports WindowAlarm Output Settings Manual Control SettingsSystem Window Status WindowsSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogMessage Explanation Log ListSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24130-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Control Description Home Window ControlsDigital zoom controls Audio controlsSave Snapshot controlsIP camera controls For related information, see the Video Window section onAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual MPEG-4 Streams Accessing the Primary MPEG-4 StreamAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24130-02 IN-1 D EIN-2 IN-3 DSCP, for QoS Dual streamingIN-4 SdramIN-5 LEDIN-6 Options OverviewIN-7 IN-8