Cisco Systems CIVS-IPC-2630V manual Setup Windows, Basic Setup Window, Option Description

Page 37

Chapter 3 Configuring and Managing the IP Camera

Setup Windows

•Status

–System

–Audio/Video

–Network

–Syslog & Log

–Video Log

Setup Windows

The Setup windows let you configure a variety of basic and advanced settings for the IP camera, and to designate IP addresses that are allowed or denied access to the IP camera.

The following sections describe the Setup windows in detail:

•Basic Setup Window, page 3-5

•Advanced Setup Window, page 3-7

•IP Filter Window, page 3-10

•EAPOL Window, page 3-11

Basic Setup Window

The Basic Setup window provides options for configuring device and network settings for the IP camera.

To display the Basic Setup window, access the configuration windows as described in the “Accessing the IP Camera Windows” section on page 2-16, click Setup, then click Basic Setup.

If you change any options except the Current Date/Time in the Basic Setup window, you must click Save to save the changes. To discard the changes, click Cancel before clicking Save. These buttons appear at the bottom of the window. You may need to scroll down to see them.

Table 3-2describes the options in the Basic Setup window.

Table 3-2 Basic Setup Window Options

Option	Description

Device Settings

Device ID	Display only. Unique identifier of the IP camera. The device ID is configured
	for the IP camera at the factory.

Camera Name	Enter a name for the IP camera. This name appears in the video log if an
	event occurs. (For related information, see the “Video Log Window” section
	on page 3-44.)
	The camera name can include any combination of up to 15 letters and
	numbers. Cisco recommends that you give each IP camera a unique name so
	that you can identify it easily.

Cisco Video Surveillance 2630 IP Dome User Guide

	OL-24130-02	3-5

Image 37

Contents Americas Headquarters Cisco Video Surveillance 2630 IP Dome User GuideCisco Video Surveillance 2630 IP Dome User Guide Iii N T E N T SSnmp Window Organization OverviewVii Viii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2630 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2630 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreparing for Installation Installing the Cisco Video Surveillance 2630 IP DomePreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Mounting with a Conduit Base ProcedureAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base Attaching the Camera to the Base Plate See -1 onCisco Video Surveillance 2630 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a PendantOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate 12 Attaching the Privacy Shield and Dome Performing the Initial Setup of the IP CameraProtocol//ipaddress Https//192.168.0.100 Accessing the IP Camera WindowsHttps//203.70.212.521024 Http//203.70.212.52Http//203.70.212.521024 Adjusting the Video Image13 Adjusting the Camera Lens on the 2630 IP Dome Resetting the IP Camera Powering the IP Camera On or OffCleaning the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Audio Window section See the Alarm I/O PortsSee the Privacy Region See the Focus/Zoom WindowSnmp Navigating the Configuration WindowsBasic Setup Window Setup WindowsDevice Settings Option DescriptionOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Controls section on Audio WindowDuplex Talk and Listen Focus/Zoom Window Privacy Region WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window Security WindowsInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsMail Setup Described in the Basic Setup Window section onPrimary Smtp Server Secondary Smtp ServerPrimary FTP Mail BodySecondary FTP Http NotificationSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window New Schedule Event ScheduleClear button Trigger EventAttachment Mail/FTP/HTTP Window section onSnmp Window Alarm Input Settings Alarm I/O Ports WindowAlarm Output Settings Manual Control SettingsSystem Window Status WindowsSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogMessage Explanation Log ListSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24130-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Control Description Home Window ControlsDigital zoom controls Audio controlsSave Snapshot controlsIP camera controls For related information, see the Video Window section onAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual MPEG-4 Streams Accessing the Primary MPEG-4 StreamAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24130-02 IN-1 D EIN-2 IN-3 DSCP, for QoS Dual streamingIN-4 SdramIN-5 LEDIN-6 Options OverviewIN-7 IN-8