Cisco Systems CIVS-IPC-2630V manual Syslog and Log Information

Page 73

Chapter 3 Configuring and Managing the IP Camera

Status Windows

Table 3-24

Syslog and Log Information (continued)

 

 

 

Message

 

Explanation

 

 

Audio: Disable microphone.

Captures information when audio devices are

 

 

enabled or disabled in the Audio window.

Audio: Disable speaker.

 

 

 

Audio: Enable microphone. (audio type: G.711

 

A-Law)

 

 

 

 

Audio: Enable microphone. (audio type: G.711

 

u-Law)

 

 

 

 

Audio: Enable microphone. (audio type: G.726)

 

 

 

Audio: Enable speaker.

 

 

 

DHCP: Lease release successfully.

Provides information about DHCP activities in

 

 

networks that include DHCP.

DHCP: Lease release unsuccessfully.

 

 

 

DHCP: Lease renewal successfully.

 

 

 

DHCP: Lease renewal unsuccessfully.

 

 

 

DHCP: Timeout error when renewing DHCP

 

lease.

 

 

 

 

DST: Adjust DST Number hour automatically.

The IP camera has automatically adjusted its clock

 

 

by the indicated number of hours for the beginning

 

 

or end of daylight saving time.

 

 

DST: DST begin.

The IP camera has adjusted its clock for the

 

 

beginning of daylight saving time.

 

 

 

DST: DST end.

 

The IP camera has adjusted its clock for the end of

 

 

daylight saving time.

 

 

LOG: Clear all messages.

You have used the Clear Log button to delete the

 

 

log file from the IP camera SDRAM.

 

 

LOG: Log file is full. Start to wrap around.

The IP camera SDRAM is full and existing log

 

 

information is beginning to be overwritten.

 

 

Network: Failed to get the IP address. Camera set

IP camera is unable to obtain an IP address

to default IP address.

through DHCP and is set to the default IP address

 

 

of 192.168.0.100.

 

 

Network: LAN activated.

IP camera obtained a network IP address.

 

 

Network: Link down.

IP camera lost connection to the network.

 

 

Network: Link up.

IP camera established connection to the network.

 

 

NTP: Failed to synchronize data & time with the

Provides information when you configure the IP

NTP server.

 

camera to obtains its time from an NTP server.

 

 

NTP: No NTP server specified.

 

 

 

NTP: Synchronization OK.

 

 

 

NTP: The NTP server cannot be reached.

 

 

 

 

 

 

Cisco Video Surveillance 2630 IP Dome User Guide

 

 

 

 

 

 

OL-24130-02

 

 

3-41

 

 

 

 

 

Image 73
Contents Americas Headquarters Cisco Video Surveillance 2630 IP Dome User GuideCisco Video Surveillance 2630 IP Dome User Guide Iii N T E N T SSnmp Window Organization OverviewVii Viii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2630 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2630 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreparing for Installation Installing the Cisco Video Surveillance 2630 IP DomePreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Mounting with a Conduit Base ProcedureAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base Attaching the Camera to the Base Plate See -1 onCisco Video Surveillance 2630 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a PendantOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate 12 Attaching the Privacy Shield and Dome Performing the Initial Setup of the IP CameraProtocol//ipaddress Https//192.168.0.100 Accessing the IP Camera WindowsHttps//203.70.212.521024 Http//203.70.212.52Http//203.70.212.521024 Adjusting the Video Image13 Adjusting the Camera Lens on the 2630 IP Dome Resetting the IP Camera Powering the IP Camera On or OffCleaning the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Audio Window section See the Alarm I/O PortsSee the Privacy Region See the Focus/Zoom WindowSnmp Navigating the Configuration WindowsBasic Setup Window Setup WindowsDevice Settings Option DescriptionOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-TLS Options Eapol WindowEAP-FAST Options Users Window, Maintenance Window, Firmware Window, Administration WindowsUsers Window User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Controls section on Audio WindowDuplex Talk and Listen Focus/Zoom Window Privacy Region WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window Security WindowsInitialization Window, Complexity Window, Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsMail Setup Described in the Basic Setup Window section onPrimary Smtp Server Secondary Smtp ServerPrimary FTP Mail BodySecondary FTP Http NotificationSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window New Schedule Event ScheduleClear button Trigger EventAttachment Mail/FTP/HTTP Window section onSnmp Window Alarm Input Settings Alarm I/O Ports WindowAlarm Output Settings Manual Control SettingsSystem Window Status WindowsSystem Status Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogMessage Explanation Log ListSystem log messages Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24130-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Control Description Home Window ControlsDigital zoom controls Audio controlsSave Snapshot controlsIP camera controls For related information, see the Video Window section onAccessing Secondary H.264 Stream Accessing the Primary H.264 StreamViewing Video through Third-Party Devices or Software Accessing Dual MPEG-4 Streams Accessing the Primary MPEG-4 StreamAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24130-02 IN-1 D EIN-2 IN-3 DSCP, for QoS Dual streamingIN-4 SdramIN-5 LEDIN-6 Options OverviewIN-7 IN-8