Cisco Systems CIVS-IPC-2630V manual Cisco Video Surveillance 2630 IP Dome User Guide

Page 20

Chapter 2 Getting Started

Installing the Cisco Video Surveillance 2630 IP Dome

Step 14 See Figure 2-13 on page 2-18and take these actions to adjust the camera lens to obtain the desired image:

•Temporarily attach an analog monitor to the IP dome so that you can see video while adjusting the camera. If the cable from the monitor terminates with a 3.5 mm jack, plug it into the analog video output port on the IP dome. If the cable terminates with a BNC connector, connect it to the mini cable with BNC adapter, then plug the cable into the analog video output port. The mini cable with BNC adapter is included in the audio/video cables accessory kit, which you can purchase from Cisco (Cisco part number CIVS-IPCA-1017=).

•Make the following adjustments, viewing the video on the analog monitor as needed:

–Back focus—The back focus is factory set for optimal use and should not require adjustments. In the event that it does need to be adjusted, use the 0.9 mm Allen wrench that is supplied with the IP camera to loosen the three back focus hex screws, then adjust the back focus by aiming the IP camera at an object that is at least 15 feet (4.5 meters) away and gently sliding the lens toward or away from the camera. Take care not to pull the lens completely away from the camera. Obtain a sharp picture in both wide-angle and telephoto positions. When the focus is set as desired, use the Allen wrench to tighten the three back focus hex screws.

–Pan—Use a Phillips-head to loosen the panning lock screw, then rotate the camera to obtain the desired image, then tighten the panning lock screw.

–Tilt—Loosen the two tilt lock screws, adjust the lens to obtain the desired image, then tighten the screws.

Caution Do not manually adjust the focus or zoom for the IP camera. Attempting to manually do so may damage the IP camera lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

Step 15 Replace the privacy shield by squeezing it to fit inside the four tabs on the camera unit (see Figure 2-6).

Make sure to adjust the privacy shield inside the dome and trim ring assembly so that it does not block the lens from capturing video.

Cisco Video Surveillance 2630 IP Dome User Guide

2-8	OL-24130-02

Image 20

Contents Cisco Video Surveillance 2630 IP Dome User Guide Americas HeadquartersCisco Video Surveillance 2630 IP Dome User Guide N T E N T S IiiSnmp Window Vii OverviewOrganization Viii Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2630 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2630 IP DomePackage Contents Getting Started Before You BeginPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2630 IP DomePreparing for Installation Passing the Audio Cable through a Ferrite Core Procedure Mounting with a Conduit BaseAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base See -1 on Attaching the Camera to the Base PlateCisco Video Surveillance 2630 IP Dome User Guide Mounting with a Pendant Attaching the Privacy Shield and DomeOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate Performing the Initial Setup of the IP Camera 12 Attaching the Privacy Shield and DomeProtocol//ipaddress Accessing the IP Camera Windows Https//192.168.0.100Https//203.70.212.521024 Http//203.70.212.52Adjusting the Video Image Http//203.70.212.52102413 Adjusting the Camera Lens on the 2630 IP Dome Powering the IP Camera On or Off Resetting the IP CameraCleaning the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Alarm I/O Ports See the Audio Window sectionSee the Privacy Region See the Focus/Zoom WindowNavigating the Configuration Windows SnmpSetup Windows Basic Setup WindowDevice Settings Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEAP-FAST Options Eapol WindowEAP-TLS Options Users Window Administration WindowsUsers Window, Maintenance Window, Firmware Window, Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Duplex Talk and Listen Audio WindowControls section on Privacy Region Window Focus/Zoom WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window, Complexity Window, Security WindowsInitialization Window Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowDescribed in the Basic Setup Window section on Mail SetupPrimary Smtp Server Secondary Smtp ServerMail Body Primary FTPSecondary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Event Schedule New ScheduleClear button Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm I/O Ports Window Alarm Input SettingsAlarm Output Settings Manual Control SettingsSystem Status Status WindowsSystem Window Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerSystem log messages Log ListMessage Explanation Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24130-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Home Window Controls Control DescriptionDigital zoom controls Audio controlsSnapshot controls SaveIP camera controls For related information, see the Video Window section onViewing Video through Third-Party Devices or Software Accessing the Primary H.264 StreamAccessing Secondary H.264 Stream Accessing the Primary MPEG-4 Stream Accessing Dual MPEG-4 StreamsAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24130-02 D E IN-1IN-2 DSCP, for QoS Dual streaming IN-3Sdram IN-4LED IN-5Options Overview IN-6IN-7 IN-8