Cisco Systems CIVS-IPC-2630V manual Adjusting the Camera Lens on the 2630 IP Dome

Page 30

Chapter 2 Getting Started

Adjusting the Video Image

or away from the camera. Take care not to pull the lens completely away from the camera.Obtain a sharp picture in both wide-angle and telephoto positions. When the focus is set as desired, use the Allen wrench to tighten the back focus hex screw.

Caution Do not manually adjust the focus or zoom for the IP camera. Attempting to manually do so may damage the IP camera lens. Instead, use the Focus/Zoom window in the configuration software to remotely set the focus and zoom for the IP camera.

Figure 2-13 Adjusting the Camera Lens on the 2630 IP Dome

1

2

1Rotation wheel

2Panning lock screw

3Tilt lock screws (2)

4Back focus hex screws (3)

3

4

Step 4 Remove the analog monitor cable from the analog video output port.

Step 5 Replace the privacy shield by squeezing it to fit inside the four tabs on the camera unit.

Make sure to adjust the privacy shield inside the dome and trim ring assembly so that it does not block the lens from capturing video.

Step 6 Align the tab on the dome assembly with the opening in the base plate, press the dome assembly into place, and securing the three TORX screws

	Cisco Video Surveillance 2630 IP Dome User Guide
2-18	OL-24130-02

Image 30

Contents Cisco Video Surveillance 2630 IP Dome User Guide Americas HeadquartersCisco Video Surveillance 2630 IP Dome User Guide N T E N T S IiiSnmp Window Overview OrganizationVii Viii Features Features, IP Camera Overview,Physical Details, Package Contents, IP Camera OverviewPhysical Details Top of the 2630 IP DomeOverview IP Camera Overview Described in the Resetting the IP Camera section on Bottom of the 2630 IP DomePackage Contents Getting Started Before You BeginInstalling the Cisco Video Surveillance 2630 IP Dome Preparing for InstallationPreventing Electrostatic Discharge Damage Passing the Audio Cable through a Ferrite Core Procedure Mounting with a Conduit BaseAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base See -1 on Attaching the Camera to the Base PlateCisco Video Surveillance 2630 IP Dome User Guide Mounting with a Pendant Attaching the Privacy Shield and DomeOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate Performing the Initial Setup of the IP Camera 12 Attaching the Privacy Shield and DomeProtocol//ipaddress Https//203.70.212.521024 Accessing the IP Camera WindowsHttps//192.168.0.100 Http//203.70.212.52Adjusting the Video Image Http//203.70.212.52102413 Adjusting the Camera Lens on the 2630 IP Dome Cleaning the IP Camera Powering the IP Camera On or OffResetting the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuring and Managing the IP Camera Configuration OverviewConfiguration Item Explanation Guidelines for Use Reference See the Privacy Region See the Alarm I/O PortsSee the Audio Window section See the Focus/Zoom WindowNavigating the Configuration Windows SnmpDevice Settings Setup WindowsBasic Setup Window Option DescriptionOption Description Advanced Setup Window Network SettingsOption BonjourOption Description IP Filter Window QoSEapol Window EAP-TLS OptionsEAP-FAST Options Administration Windows Users Window, Maintenance Window, Firmware Window,Users Window Administrator User ListMaintenance Window Firmware Window Audio/Video Windows Video WindowDual Streams MPEG-4 + Mjpeg -Configures MPEG-4 for SettingsMPEG-4 Settings Mjpeg Settings Resolution Choose the resolution of the Mjpeg video streamVideo Adjustment PAL/50 HzOptions Day/Night VisionOption Description Audio Window Controls section onDuplex Talk and Listen Choose Simplex Talk Only , Half Duplex Talk or Listen , or Privacy Region WindowFocus/Zoom Window Full Duplex Talk and ListenSecurity Windows Initialization WindowInitialization Window, Complexity Window, Complexity Window Users Window section onApplications Windows Mail/FTP/HTTP WindowPrimary Smtp Server Described in the Basic Setup Window section onMail Setup Secondary Smtp ServerSecondary FTP Mail BodyPrimary FTP Http NotificationMotion Detection Window System-provided-name-value-pairs is the event informationEvent Window Clear button Event ScheduleNew Schedule Trigger EventMail/FTP/HTTP Window section on AttachmentSnmp Window Alarm Output Settings Alarm I/O Ports WindowAlarm Input Settings Manual Control SettingsStatus Windows System WindowSystem Status Audio Setting Audio/Video WindowNetwork Window Syslog & Log WindowLocal Log Sys Log ServerLog List Message ExplanationSystem log messages Syslog and Log Information Address Address1 Port1 Address2 Port2 , User FTP log messagesVideo Log Window Smtp log messagesDelete button Delete All buttonOL-24130-02 Viewing Video through the Home Window Overview Home Window OverviewHome Window Digital zoom controls Home Window ControlsControl Description Audio controlsIP camera controls Snapshot controlsSave For related information, see the Video Window section onAccessing the Primary H.264 Stream Accessing Secondary H.264 StreamViewing Video through Third-Party Devices or Software Accessing the Mjpeg Stream Accessing the Primary MPEG-4 StreamAccessing Dual MPEG-4 Streams Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting Using the IP Camera with Cisco VSM For instructions, see the Video Window section onOL-24130-02 D E IN-1IN-2 DSCP, for QoS Dual streaming IN-3Sdram IN-4LED IN-5Options Overview IN-6IN-7 IN-8