Cisco Systems CIVS-IPC-2630V manual Option Description

Page 41

Chapter 3 Configuring and Managing the IP Camera

Setup Windows

Table 3-3

Advanced Setup Window Options (continued)

 

 

 

Option

 

Description

 

 

Max RTP Video Packet

Maximum number of bytes per video packet that are sent in each RTP

Length

 

request.

 

 

Configure a lower number if you are streaming video to a cell phone that

 

 

requires smaller data packets.

 

 

Valid values are 400 through 1400. The default value is 1400.

 

 

Max RTP Audio Packet

Maximum number of bytes per audio packet that are sent in each RTP

 

 

request.

 

 

Configure a lower number if you are streaming video to a cell phone that

 

 

requires smaller data packets.

 

 

Valid values are 400 through 1400. The default value is 1400.

 

 

Enable Multicast

Check this check box to send video and audio data as a multicast stream.

 

 

When multicast is enabled, the IP camera sends video and audio to the

 

 

multicast addresses that you designate. Multicast enables multiple devices to

 

 

receive the video signal from the IP camera simultaneously.

 

 

 

Video Address

 

Appears if you enabled multicast. Enter the multicast IP address on which

 

 

the IP camera sends a video stream.

 

 

The default value is 224.2.0.1.

 

 

 

Video Port

 

Appears if you enabled multicast. Enter the port on which the IP camera

 

 

sends a multicast video stream.

 

 

Valid values are even numbers 1024 through 65534. The default value is

 

 

2240.

 

 

 

Audio Address

 

Appears if you enabled multicast. Enter the multicast IP address on which

 

 

the IP camera sends an audio stream.

 

 

The default value is 224.2.0.1.

 

 

 

Audio Port

 

Appears if you enabled multicast. Enter the port on which the IP camera

 

 

sends a multicast audio stream.

 

 

Valid values are even numbers 1024 through 65534. The default value is

 

 

2242.

 

 

 

Time to Live

 

Appears if you enabled multicast. Enter the number of hops, which specifies

 

 

the number of network devices that an audio-video stream can pass before

 

 

arriving at its destination or being dropped.

 

 

Valid values are 1 through 255. The default value is 16.

 

 

 

Cisco Video Surveillance 2630 IP Dome User Guide

 

OL-24130-02

3-9

 

 

 

Image 41
Contents Americas Headquarters Cisco Video Surveillance 2630 IP Dome User GuideCisco Video Surveillance 2630 IP Dome User Guide Iii N T E N T SSnmp Window Vii OverviewOrganization Viii Features, IP Camera Overview, FeaturesIP Camera Overview Physical Details, Package Contents,Top of the 2630 IP Dome Physical DetailsOverview IP Camera Overview Bottom of the 2630 IP Dome Described in the Resetting the IP Camera section onPackage Contents Before You Begin Getting StartedPreventing Electrostatic Discharge Damage Installing the Cisco Video Surveillance 2630 IP DomePreparing for Installation Passing the Audio Cable through a Ferrite Core Mounting with a Conduit Base ProcedureAttaching the Conduit Base to a Ceiling or Wall Attaching Base Plate to Conduit Base Attaching the Camera to the Base Plate See -1 onCisco Video Surveillance 2630 IP Dome User Guide Attaching the Privacy Shield and Dome Mounting with a PendantOL-24130-02 Pendant Gasket Conduit base 10 Attaching the Base Plate to the Conduit 11 Attaching the Camera to the Base Plate 12 Attaching the Privacy Shield and Dome Performing the Initial Setup of the IP CameraProtocol//ipaddress Https//192.168.0.100 Accessing the IP Camera WindowsHttps//203.70.212.521024 Http//203.70.212.52Http//203.70.212.521024 Adjusting the Video Image13 Adjusting the Camera Lens on the 2630 IP Dome Resetting the IP Camera Powering the IP Camera On or OffCleaning the IP Camera Reset Type Procedure RemarksOL-24130-02 Configuration Overview Configuring and Managing the IP CameraConfiguration Item Explanation Guidelines for Use Reference See the Audio Window section See the Alarm I/O PortsSee the Privacy Region See the Focus/Zoom WindowSnmp Navigating the Configuration WindowsBasic Setup Window Setup WindowsDevice Settings Option DescriptionOption Description Network Settings Advanced Setup WindowBonjour OptionOption Description QoS IP Filter WindowEAP-FAST Options Eapol WindowEAP-TLS Options Users Window Administration WindowsUsers Window, Maintenance Window, Firmware Window, User List AdministratorMaintenance Window Firmware Window Video Window Audio/Video WindowsSettings Dual Streams MPEG-4 + Mjpeg -Configures MPEG-4 forMPEG-4 Settings Resolution Choose the resolution of the Mjpeg video stream Mjpeg SettingsPAL/50 Hz Video AdjustmentDay/Night Vision OptionsOption Description Duplex Talk and Listen Audio WindowControls section on Focus/Zoom Window Privacy Region WindowChoose Simplex Talk Only , Half Duplex Talk or Listen , or Full Duplex Talk and ListenInitialization Window, Complexity Window, Security WindowsInitialization Window Users Window section on Complexity WindowMail/FTP/HTTP Window Applications WindowsMail Setup Described in the Basic Setup Window section onPrimary Smtp Server Secondary Smtp ServerPrimary FTP Mail BodySecondary FTP Http NotificationSystem-provided-name-value-pairs is the event information Motion Detection WindowEvent Window New Schedule Event ScheduleClear button Trigger EventAttachment Mail/FTP/HTTP Window section onSnmp Window Alarm Input Settings Alarm I/O Ports WindowAlarm Output Settings Manual Control SettingsSystem Status Status WindowsSystem Window Audio/Video Window Audio SettingSyslog & Log Window Network WindowSys Log Server Local LogSystem log messages Log ListMessage Explanation Syslog and Log Information Address FTP log messages Address1 Port1 Address2 Port2 , UserSmtp log messages Video Log WindowDelete All button Delete buttonOL-24130-02 Home Window Overview Viewing Video through the Home Window OverviewHome Window Control Description Home Window ControlsDigital zoom controls Audio controlsSave Snapshot controlsIP camera controls For related information, see the Video Window section onViewing Video through Third-Party Devices or Software Accessing the Primary H.264 StreamAccessing Secondary H.264 Stream Accessing Dual MPEG-4 Streams Accessing the Primary MPEG-4 StreamAccessing the Mjpeg Stream Accessing Dual Streams H.264 + MjpegAccessing Dual Streams MPEG-4 + Mjpeg OL-24130-02 Troubleshooting Troubleshooting For instructions, see the Video Window section on Using the IP Camera with Cisco VSMOL-24130-02 IN-1 D EIN-2 IN-3 DSCP, for QoS Dual streamingIN-4 SdramIN-5 LEDIN-6 Options OverviewIN-7 IN-8